Difference between revisions of "Prusa MK3S+"

From Asmbly Wiki
(→‎Maintenance: Add link to regular maintenance)
 
(11 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
{{Required|Intro to Filament 3D Printing}}
 
{{Required|Intro to Filament 3D Printing}}
 +
 +
Asmbly has three Prusa i3 MK3S+ 3D Printers. In the Multi-Purpose Room, these are the three smaller machines in the large enclosure.  The one on the left is named Apollo, and the middle is named Hermes, and the rightmost is Sunwukong.
 +
 
{{ToolPhoto|Prusa_MK3S.jpg}}
 
{{ToolPhoto|Prusa_MK3S.jpg}}
  
−
Asmbly has three Prusa i3 MK3S+ 3D Printers.  As of now, these are the recommended 3D printers for new users and will be covered in the Intro to 3D Printing class. These printers live to the left in the printing enclosure. The one on the left is named Apollo, and the middle is named Hermes, and the rightmost is Sunwukong.
+
{| class="wikitable" width="100%" style="text-align: center; margin: auto"
−
 
 
−
{|class="wikitable" width="100%" style="text-align: center; margin: auto"
 
 
|+ASMBLY Prusa i3 MK3S+ Printers
 
|+ASMBLY Prusa i3 MK3S+ Printers
 
|-
 
|-
Line 16: Line 17:
 
| WebInterface = Octoprint, Device Screen & Buttons
 
| WebInterface = Octoprint, Device Screen & Buttons
 
| Nozzle Size (mm) = 0.4
 
| Nozzle Size (mm) = 0.4
−
| Nozzle Type = Hardened Steel
+
| Nozzle Type = Revo ObXidian (Abrasives Allowed)
 
| Nozzle Count = 1
 
| Nozzle Count = 1
 
| Filament Size (mm) = 1.75
 
| Filament Size (mm) = 1.75
Line 24: Line 25:
 
| Max Print Speed (mm/s) = 100
 
| Max Print Speed (mm/s) = 100
 
| Extruder Type = Direct
 
| Extruder Type = Direct
 +
| Manual = [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf MK3S+ Handbook]
 
}}
 
}}
 
||
 
||
Line 34: Line 36:
 
| WebInterface = Octoprint, Device Screen & Buttons
 
| WebInterface = Octoprint, Device Screen & Buttons
 
| Nozzle Size (mm) = 0.4
 
| Nozzle Size (mm) = 0.4
−
| Nozzle Type = Hardened Steel
+
| Nozzle Type = Revo ObXidian (Abrasives Allowed)
 
| Nozzle Count = 1
 
| Nozzle Count = 1
 
| Filament Size (mm) = 1.75
 
| Filament Size (mm) = 1.75
Line 42: Line 44:
 
| Max Print Speed (mm/s) = 100
 
| Max Print Speed (mm/s) = 100
 
| Extruder Type = Direct
 
| Extruder Type = Direct
 +
| Manual = [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf MK3S+ Handbook]
 
}}
 
}}
 
||
 
||
Line 52: Line 55:
 
| WebInterface = Octoprint, Device Screen & Buttons
 
| WebInterface = Octoprint, Device Screen & Buttons
 
| Nozzle Size (mm) = 0.4
 
| Nozzle Size (mm) = 0.4
−
| Nozzle Type = Hardened Steel
+
| Nozzle Type = Revo ObXidian (Abrasives Allowed)
 
| Nozzle Count = 1
 
| Nozzle Count = 1
 
| Filament Size (mm) = 1.75
 
| Filament Size (mm) = 1.75
Line 60: Line 63:
 
| Max Print Speed (mm/s) = 100
 
| Max Print Speed (mm/s) = 100
 
| Extruder Type = Direct
 
| Extruder Type = Direct
 +
| Manual = [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf MK3S+ Handbook]
 
}}
 
}}
 
|}
 
|}
  
 +
== Safety==
  
−
The printers are controllable over Octoprint, which you can use the web browser or an app to connect to while on the ASMBLY network. You cannot access these machines from home. Tasks such as preheating and filament changes can be done via the built-in panel on the front bottom of the printer. The Octoprint configuration is the standard OctoPi installation, consisting of the Raspberry Pi 3 or 4 being attached to the back of the printer frame, connected via USB to the printer and via Ethernet to the ASMBLY network (WiFi connection from the Pi to the network is currently unstable), with the OctoPi 1.0.0 (build 2023.10.09.151442) stable image installed on the Pi. In an attempt to keep the printers as easily serviced and maintained, we are trying to keep the installation as standard as possible. More documentation about OctoPi can be found [https://help.prusa3d.com/article/octoprint-configuration-and-install_2182 here]. Files for printing replacement Pi 3B and Pi 4B cases can be found at the page bottom.
+
{{UniversalSafety}}
  
 +
====Equipment-Specific Safety====
 +
[[Intro to Filament 3D Printing Class]] is required to use this tool.
 +
 +
No special PPE is required to use this tool.
 +
 +
==== Etiquette====
 +
 +
Time booked for 3D printing in [https://asmbly.skedda.com Skedda] does not count against your weekly Asmbly hours. It is fine to book long blocks of time when printing large objects. It is fine for a print to continue while Asmbly is closed. Please only reserve the time you need, and if you finish early or realize you can't make use of your time, please cancel the remainder of your reservation.
 +
 +
If you come in for your scheduled time and a print has finished, feel free to move it and any filament on the machine to the table to the left of the enclosure.
 +
 +
If you are in the 3D printing area and see a print in progress that is obviously failing, it is a good idea to stop the print so that it stops wasting filament. Try to contact the person who has that printer booked in Skedda to let them know. [https://yo.asmbly.org Discourse] is a good way to do that, if you don't already know them.
 +
 +
You may find a cut-off piece of filament still in the nozzle when you arrive. This is because the nozzle was cold when the previous user retrieved their filament and they didn't want to wait for it to heat up again. When you heat the nozzle for your own print, just unload the stub.
 +
 +
== Use Case==
 +
[[File:Threeprusai3s.jpg|alt=Apollo, Hermes, and Sunwukong|thumb|All three printers]]
 +
The Prusa MK3S+ are good printers to produce small and medium sized objects using a single filament using many common filament types. The printer only uses one filament at a time, so if you want to print with multiple filaments, you will have to manually change filaments mid-print.
 +
 +
If you need to print larger things or to use multiple filaments without manually changing them, use the [[Prusa XL]].
 +
 +
If you need to print in ABS, ASA, or other materials that print better enclosed, consider using the [[PolyPrinter 229]].
 +
 +
Use [https://asmbly.skedda.com Skedda] to reserve time on the specific printer. 
 +
 +
==Materials==
 +
 +
====Acceptable Materials====
 +
 +
Many types of 1.75mm filament will work with these printers. There is a pair of spool rollers if you have a spool that is too large to fit on the spool holder.
 +
 +
These printers have been equipped with abrasion-resistant [https://e3d-online.com/products/revo-obxidian-nozzles ObXidian nozzles]. This means that filaments that include additives like glow-in-the-dark (strontium aluminate), carbon fiber, glass fiber, wood, or metal are acceptable to use with these machines.
 +
 +
====Material Limits====
 +
 +
Print volume is 250mm x 210mm x 210mm (9.8" x 8.2" x 8.2")
 +
 +
==== Consumables====
 +
 +
You are responsible for providing your own filament. There are many places to order from, including [https://www.matterhackers.com/ MatterHackers], [https://www.prusa3d.com/category/filament/ Prusa], [https://polymaker.com/ Polymaker], and Amazon. We are not currently aware of any place to buy filament locally, but if you know of one, we'd be interested!
 +
 +
There are some SD cards in the tool caddy, but if you find yourself printing from SD a lot consider bringing your own.
 +
 +
Asmbly provides a selection of Prusa steel sheets in three different textures: Textured, Satin, and Smooth. We don't have three of each, so it's possible that your preferred sheet will be in use when you want to print. Asmbly also provides cleaners for the sheets: Isopropyl Alcohol (usually in a squeeze bottle with the printer tools) and Dish Soap (in the coffee area just outside of the multi-purpose room.
 +
==Operation==
 +
 +
====Controls====
 +
 +
====== Emergency Stop ======
 +
If you see or hear something going terribly wrong with the printer, you can immediately stop it by pressing the <code>X</code> button below the dial control. This is equivalent to unplugging the printer and plugging it back in. Examples of situations where you would want to do this: the nozzle is contacting the steel plate, the printer is trying to move the head beyond its rails.
 +
 +
If you just need to stop a print, please press the dial control and select <code>Stop Print</code>. The <code>X</code> button sometimes causes the printer to lose some of its settings and need to be recalibrated, so avoid using it for things you can stop normally. But if you are in doubt, do use the <code>X</code> button.
 +
 +
====== Control Panel ======
 +
Each printer has a control panel that can be used to do things like preheating the machine, loading and unloading filament, pausing/stopping a print, and starting a print from an SD card.
 +
 +
====== Octoprint ======
 +
Each printer is also equipped with a dedicated Octoprint server:
 +
 +
*http://apollo-printer.local
 +
*http://hermes-printer.local
 +
*http://sunwukong-printer.local
 
'''Login information: The username is "User", and the password is the ASMBLY WiFi password (Look around the space for plaques that state this information, or find a steward).'''
 
'''Login information: The username is "User", and the password is the ASMBLY WiFi password (Look around the space for plaques that state this information, or find a steward).'''
  
 +
Octoprint allows you connect from the Asmbly WiFi network with a web browser or an app and start/stop a print and monitor things like the current temperature. You can't access these machines from home, you must be physically present at Asmbly.
 +
 +
Because the Octoprint servers are now installed individually to each printer, it is safe to reboot a printer and Octoprint without disrupting the other printers in operation. This was not the case with the previous printers.
 +
 +
====== Stopping or Pausing a print ======
 +
You can stop a print from either Octoprint or the control panel. If you stop or pause a print from Octoprint, it will not move the nozzle clear of your print. If you hope to resume, it is probably better to do this from the control panel.
 +
======Firmware Upgrade Warning======
 +
Ignore messages about a firmware upgrade warning- the printers had to be downgraded to Firmware 3.12 in order to use the Revo nozzles. We have not yet been able to get the newest firmware working with Revo (including the Revo specific firmware). 
 +
====Settings and Adjustments====
  
−
== Maintenance ==
+
====== Filament ======
 +
Make sure that your gcode is sliced for the particular kind of filament you're using. You can select the filament type on the control panel, and adjust the bed and nozzle temperatures.
  
 +
====== Print Bed Sheet ======
 +
{{Note|type=error|text=🛑 DO NOT PRINT DIRECTLY ON THE BED. ALWAYS USE A STEEL SHEET.}}
 +
[[File:Prusa MK3S+ Display.jpg|alt=The Prusa MK3S+ display showing that the Smooth1 sheet is active|thumb|Calibrated for Smooth1]]
 +
Asmbly provides three different kinds of Prusa sheets:
 +
 +
* [https://www.prusa3d.com/product/textured-powder-coated-steel-sheet/ Textured Powder-coated Steel Sheet]
 +
* [https://www.prusa3d.com/product/satin-powder-coated-steel-sheet/ Satin Powder-coated Steel Sheet]
 +
* [https://www.prusa3d.com/product/smooth-pei-steel-sheet/ Smooth PEI Steel Sheet]
 +
 +
There is a chart on the enclosure that lists which sheets are best for each kind of filament, or check Section 6.3.2 of the [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf handbook]
 +
 +
Make sure that the printer knows which sheet is on it. The sheets have different thicknesses, and you may not get a good first layer if the wrong sheet is selected.
 +
 +
====== Nozzles / Hotend ======
 +
All three Prusa i3 mk3s+ printers have been upgraded with the E3D Revo hotend (from the stock E3D V6). They are all equipped with the 0.4mm abrasion-resistance ObXidian nozzles. '''Please do not change the nozzles'''. We upgraded to the Revo to improve ease of maintenance and reliability of the printers, but do not currently have a system to support nozzle size changes. 
 +
 +
==Cleanup==
 +
 +
{{UniversalCleaning}}
 +
 +
====Tool Specific Cleaning Guide====
 +
 +
* Remove any scraps of filament from the enclosure
 +
* Return any tools you used to the tool caddy
 +
* Make sure the steel sheet you used is clear of any leftover filament
 +
 +
==Resources==
 +
 +
====Manual====
 +
 +
*[https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf User Manual]
 +
*[[PrusaSlicer]]
 +
*[[3D Filament Temperature Tower]] - Fine tune your temperature settings for a particular filament
 +
 +
====Discourse Links====
 +
[https://yo.asmbly.org/c/spaces/3dprinters/11 yo.asmbly.org]
 +
 +
====External Resources====
 +
Places to find models to print:
 +
 +
* [https://www.stlfinder.com/#google_vignette STLFinder]
 +
* [https://www.thingiverse.com/ Thingiverse]
 +
* [https://www.printables.com/ Printables]
 +
* [https://www.yeggi.com/ Yeggi]
 +
* Buy from makers on Etsy
 +
* [https://www.myminifactory.com/ MyMiniFactory] for DnD miniatures
 +
 +
Places to buy filament:
 +
 +
* [https://www.matterhackers.com/ MatterHackers]
 +
 +
* [https://www.prusa3d.com/category/filament/ Prusa]
 +
 +
* [https://polymaker.com/ Polymaker]
 +
* Amazon
 +
 +
==Troubleshooting==
 +
 +
====Common Problems====
 +
 +
====== Model not sticking to the sheet ======
 +
If you are having trouble with getting your first layer to stick properly try these:
 +
 +
# Double check that the printer is configured for the right sheet
 +
# Clean the '''cool''' sheet with Isopropyl Alcohol (in a squeeze bottle with the other tools)
 +
# Wash the sheet with dish soap at the coffee area sink. '''Make sure the sheet is completely dry before reinstalling it.'''
 +
# Adjust the Z calibration. You can do this by going through the <code>Calibration > First Layer Calibration</code> process on the control panel (Section 6.3.9 of the [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf handbook]). You can also adjust it live while your first layer prints (Press the control wheel while printing, select <code>Live adjust Z</code> ). If you find that you need to set a Z value beyond -2.000mm, please file a problem report. You can continue your print, but this indicates that the Z sensor needs to be adjusted.
 +
# Contact a steward
 +
 +
====== Nozzle has plastic stuck to it ======
 +
This often happens as a result of the model not sticking to the sheet, and causes problems when you try again.
 +
{{Note|type=warning|text=⚠️ The nozzle is probably very hot! Don't touch it with something that will burn... like your fingers!}}
 +
 +
# Use <code>Settings > Move axis > Move Z</code> to raise the nozzle so you can see under it
 +
# Touch some cool plastic to the still-hot plastic on the nozzle. It should stick and let you pull the mess away
 +
# Heat the nozzle above the printing temperature for your filament, for example, try 250° for PLA, which normally prints around 215°. Wait for the nozzle to heat up and let the melted plastic drip off of the nozzle
 +
# Use the tweezers from the tool caddy to grab larger lumps
 +
# Use the soft-bristled brush in the tool caddy to wipe the warm nozzle
 +
 +
====== Other ======
 +
If you are unsure, it is always best to contact a steward and fill out a [https://docs.google.com/forms/d/e/1FAIpQLSfBhIcxwJPpBbuTVlxZ6-hSfNduEM5kkT0e4JP_uxGe9Ar75Q/viewform problem report]
 +
 +
==Maintenance==
 +
The information below is primarily for stewards.
 +
 +
==== Regular Maintenance ====
 +
The lead screws should be cleaned and lubricated regularly. This video provides a good walkthrough: [https://www.youtube.com/watch?v=7AzW-bWefrk How To Service Your Prusa i3 MK3]
 +
 +
==== Octoprint ====
 +
[https://help.prusa3d.com/article/octoprint-configuration-and-install_2182 Octoprint - Configuration and install]
 +
 +
The Octoprint configuration is the standard OctoPi installation, consisting of the Raspberry Pi 3 or 4 being attached to the back of the printer frame, connected via USB to the printer and via Ethernet to the ASMBLY network (WiFi connection from the Pi to the network is currently unstable), with the OctoPi 1.0.0 (build 2023.10.09.151442) stable image installed on the Pi. In an attempt to keep the printers as easily serviced and maintained, we are trying to keep the installation as standard as possible. More documentation about OctoPi can be found [https://help.prusa3d.com/article/octoprint-configuration-and-install_2182 here]. Files for printing replacement Pi 3B and Pi 4B cases can be found here:
 +
 +
*[https://www.thingiverse.com/thing:4425749 Pi 4 Case with Prusa i3 Mounting]
 +
*[https://www.thingiverse.com/thing:3004038 Pi 3 Case with Prusa i3 Mounting]
 +
 +
==== Moving the printers ====
 
Due to the Octoprint installation on the printers, take extra care to make sure not only the main power cable is unplugged from the printer, but also the ethernet cable and the USB power cable connected to the Pi mounted to the back-upper-left corner of the printer when moving the printer around or out of the enclosure. Remember to reconnect these later.  
 
Due to the Octoprint installation on the printers, take extra care to make sure not only the main power cable is unplugged from the printer, but also the ethernet cable and the USB power cable connected to the Pi mounted to the back-upper-left corner of the printer when moving the printer around or out of the enclosure. Remember to reconnect these later.  
  
−
== Rebooting Procedure ==
+
====Rebooting Procedure====
−
 
 
−
In order to fully reboot the printer and the Octoprint server attached to it, power off the Pi at the back-upper-left of the printer by toggling it's inline power switch, and turn the printer off using the power switch on the power supply unit at the back of the printer. Then toggle the power supply unit switch back on, and then turn the Pi back on. The Octoprint page should be reachable in under one minute.
 
  
−
Because the Octoprint servers are now installed individually to each printer, it is safe to reboot a printer and Octoprint without disrupting the other printers in operation. This was not the case with the previous printers.
+
In order to fully reboot the printer and the Octoprint server attached to it, power off the Pi at the back-upper-left of the printer by toggling its inline power switch, and turn the printer off using the power switch on the power supply unit at the back of the printer. Then toggle the power supply unit switch back on, and then turn the Pi back on. The Octoprint page should be reachable in under one minute.
  
−
{{ToolPhoto|Threeprusai3s.jpg}}
+
==== Z Problems ====
 +
If the printer is printing too far away or too close to the bed for the first layer (to see what these look like look at Section 6.3.9 of the [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf handbook]), the Z probably needs to be fine tuned. Try this:
  
−
== Resources ==
+
# Make sure the printer knows which sheet is on the bed. Different sheets have different calibrations
−
* [[Media:Prusa MK3S Handbook.pdf|User Manual]]
+
# Run through the <code>Calibration > First Layer Calibration</code> process on the control panel (Section 6.3.9 of the [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf handbook])
−
* [https://help.prusa3d.com/article/octoprint-configuration-and-install_2182 Octoprint - Configuration and install]
+
# If you have trouble calibrating Z using just the First Layer Calibration, or you want to check the calibration, these models have been useful. They may already be on the printer in a directory named Calibration. If not, create that directory and/or add these files.
−
* [https://www.thingiverse.com/thing:4425749 Pi 4 Case with Prusa i3 Mounting]
+
## [[:File:First layer calibration network.stl|Calibration Network]]
−
* [https://www.thingiverse.com/thing:3004038 Pi 3 Case with Prusa i3 Mounting]
+
## [[:File:First layer calibration E.stl|Calibration E]]
 +
# If you have to set the Z further out than -2.000mm, the Z sensor probably needs to be adjusted. See 6.3.10.2 of the handbook
 +
## The proper height for the sensor is about a [https://help.prusa3d.com/guide/how-to-replace-superpinda-mk3s-mk3s_179920#181423 zip tie's thickness]
 +
## If you move the Z sensor, do a Z Calibration, then calibrate the first layer again. You'll need to do this for all three sheet types, Textured, Satin, and Smooth.
  
−
{{Owned}}
 
 
[[Category:3D Printing]]
 
[[Category:3D Printing]]

Latest revision as of 05:04, 5 November 2024

ClassWarningIcon.png Members must complete the Intro to Filament 3D Printing Class before using this tool



Asmbly has three Prusa i3 MK3S+ 3D Printers. In the Multi-Purpose Room, these are the three smaller machines in the large enclosure. The one on the left is named Apollo, and the middle is named Hermes, and the rightmost is Sunwukong.


Prusa MK3S.jpg


ASMBLY Prusa i3 MK3S+ Printers
Apollo
Status Active
Manufacturer Prusa
Model i3 MK3S+ & Pi 3B
Nozzle Size 0.4mm
Nozzle Type Revo ObXidian (Abrasives Allowed)
Nozzle Count 1
Filament Size 1.75mm
Print Volume 250 x 210 x 210mm
Max Bed Temperature 122C
Max Nozzle Temperature 295C
Max Print Speed 100mm/s
Extruder Type Direct
Manual MK3S+ Handbook
Control Interface Octoprint, Device Screen & Buttons
Network Address http://apollo-printer.local/


Hermes
Status Active
Manufacturer Prusa
Model i3 MK3S+ & Pi 4B
Nozzle Size 0.4mm
Nozzle Type Revo ObXidian (Abrasives Allowed)
Nozzle Count 1
Filament Size 1.75mm
Print Volume 250 x 210 x 210mm
Max Bed Temperature 122C
Max Nozzle Temperature 295C
Max Print Speed 100mm/s
Extruder Type Direct
Manual MK3S+ Handbook
Control Interface Octoprint, Device Screen & Buttons
Network Address http://hermes-printer.local/


Sunwukong
Status Active
Manufacturer Prusa
Model i3 MK3S+ & Pi 4B
Nozzle Size 0.4mm
Nozzle Type Revo ObXidian (Abrasives Allowed)
Nozzle Count 1
Filament Size 1.75mm
Print Volume 250 x 210 x 210mm
Max Bed Temperature 122C
Max Nozzle Temperature 295C
Max Print Speed 100mm/s
Extruder Type Direct
Manual MK3S+ Handbook
Control Interface Octoprint, Device Screen & Buttons
Network Address http://sunwukong-printer.local/


Safety

Universal Safety

  • Be aware of your surroundings, especially when handling large materials.
  • Do not approach anyone operating equipment. Stand patiently in their field of view.
  • Use PPE, including filtration and eye protection, when handling dust or emptying dust/shaving containers.

Equipment-Specific Safety

Intro to Filament 3D Printing Class is required to use this tool.

No special PPE is required to use this tool.

Etiquette

Time booked for 3D printing in Skedda does not count against your weekly Asmbly hours. It is fine to book long blocks of time when printing large objects. It is fine for a print to continue while Asmbly is closed. Please only reserve the time you need, and if you finish early or realize you can't make use of your time, please cancel the remainder of your reservation.

If you come in for your scheduled time and a print has finished, feel free to move it and any filament on the machine to the table to the left of the enclosure.

If you are in the 3D printing area and see a print in progress that is obviously failing, it is a good idea to stop the print so that it stops wasting filament. Try to contact the person who has that printer booked in Skedda to let them know. Discourse is a good way to do that, if you don't already know them.

You may find a cut-off piece of filament still in the nozzle when you arrive. This is because the nozzle was cold when the previous user retrieved their filament and they didn't want to wait for it to heat up again. When you heat the nozzle for your own print, just unload the stub.

Use Case

Apollo, Hermes, and Sunwukong
All three printers

The Prusa MK3S+ are good printers to produce small and medium sized objects using a single filament using many common filament types. The printer only uses one filament at a time, so if you want to print with multiple filaments, you will have to manually change filaments mid-print.

If you need to print larger things or to use multiple filaments without manually changing them, use the Prusa XL.

If you need to print in ABS, ASA, or other materials that print better enclosed, consider using the PolyPrinter 229.

Use Skedda to reserve time on the specific printer.

Materials

Acceptable Materials

Many types of 1.75mm filament will work with these printers. There is a pair of spool rollers if you have a spool that is too large to fit on the spool holder.

These printers have been equipped with abrasion-resistant ObXidian nozzles. This means that filaments that include additives like glow-in-the-dark (strontium aluminate), carbon fiber, glass fiber, wood, or metal are acceptable to use with these machines.

Material Limits

Print volume is 250mm x 210mm x 210mm (9.8" x 8.2" x 8.2")

Consumables

You are responsible for providing your own filament. There are many places to order from, including MatterHackers, Prusa, Polymaker, and Amazon. We are not currently aware of any place to buy filament locally, but if you know of one, we'd be interested!

There are some SD cards in the tool caddy, but if you find yourself printing from SD a lot consider bringing your own.

Asmbly provides a selection of Prusa steel sheets in three different textures: Textured, Satin, and Smooth. We don't have three of each, so it's possible that your preferred sheet will be in use when you want to print. Asmbly also provides cleaners for the sheets: Isopropyl Alcohol (usually in a squeeze bottle with the printer tools) and Dish Soap (in the coffee area just outside of the multi-purpose room.

Operation

Controls

Emergency Stop

If you see or hear something going terribly wrong with the printer, you can immediately stop it by pressing the X button below the dial control. This is equivalent to unplugging the printer and plugging it back in. Examples of situations where you would want to do this: the nozzle is contacting the steel plate, the printer is trying to move the head beyond its rails.

If you just need to stop a print, please press the dial control and select Stop Print. The X button sometimes causes the printer to lose some of its settings and need to be recalibrated, so avoid using it for things you can stop normally. But if you are in doubt, do use the X button.

Control Panel

Each printer has a control panel that can be used to do things like preheating the machine, loading and unloading filament, pausing/stopping a print, and starting a print from an SD card.

Octoprint

Each printer is also equipped with a dedicated Octoprint server:

Login information: The username is "User", and the password is the ASMBLY WiFi password (Look around the space for plaques that state this information, or find a steward).

Octoprint allows you connect from the Asmbly WiFi network with a web browser or an app and start/stop a print and monitor things like the current temperature. You can't access these machines from home, you must be physically present at Asmbly.

Because the Octoprint servers are now installed individually to each printer, it is safe to reboot a printer and Octoprint without disrupting the other printers in operation. This was not the case with the previous printers.

Stopping or Pausing a print

You can stop a print from either Octoprint or the control panel. If you stop or pause a print from Octoprint, it will not move the nozzle clear of your print. If you hope to resume, it is probably better to do this from the control panel.

Firmware Upgrade Warning

Ignore messages about a firmware upgrade warning- the printers had to be downgraded to Firmware 3.12 in order to use the Revo nozzles. We have not yet been able to get the newest firmware working with Revo (including the Revo specific firmware).

Settings and Adjustments

Filament

Make sure that your gcode is sliced for the particular kind of filament you're using. You can select the filament type on the control panel, and adjust the bed and nozzle temperatures.

Print Bed Sheet

🛑 DO NOT PRINT DIRECTLY ON THE BED. ALWAYS USE A STEEL SHEET.

The Prusa MK3S+ display showing that the Smooth1 sheet is active
Calibrated for Smooth1

Asmbly provides three different kinds of Prusa sheets:

There is a chart on the enclosure that lists which sheets are best for each kind of filament, or check Section 6.3.2 of the handbook

Make sure that the printer knows which sheet is on it. The sheets have different thicknesses, and you may not get a good first layer if the wrong sheet is selected.

Nozzles / Hotend

All three Prusa i3 mk3s+ printers have been upgraded with the E3D Revo hotend (from the stock E3D V6). They are all equipped with the 0.4mm abrasion-resistance ObXidian nozzles. Please do not change the nozzles. We upgraded to the Revo to improve ease of maintenance and reliability of the printers, but do not currently have a system to support nozzle size changes.

Cleanup

Universal Cleaning Guide

  • Return the equipment to neutral.
  • Sweep up any dust and debris around the tool, your table top, and the floor - both in the equipment area and your work area.
  • Clear the floor of any tripping hazards, like power cords.
  • Empty trash cans and dust collectors that are halfway full or more into the Asmbly dumpster behind the workshop.
  • Leave the shop 110% better than you found it.

Tool Specific Cleaning Guide

  • Remove any scraps of filament from the enclosure
  • Return any tools you used to the tool caddy
  • Make sure the steel sheet you used is clear of any leftover filament

Resources

Manual

Discourse Links

yo.asmbly.org

External Resources

Places to find models to print:

Places to buy filament:

Troubleshooting

Common Problems

Model not sticking to the sheet

If you are having trouble with getting your first layer to stick properly try these:

  1. Double check that the printer is configured for the right sheet
  2. Clean the cool sheet with Isopropyl Alcohol (in a squeeze bottle with the other tools)
  3. Wash the sheet with dish soap at the coffee area sink. Make sure the sheet is completely dry before reinstalling it.
  4. Adjust the Z calibration. You can do this by going through the Calibration > First Layer Calibration process on the control panel (Section 6.3.9 of the handbook). You can also adjust it live while your first layer prints (Press the control wheel while printing, select Live adjust Z ). If you find that you need to set a Z value beyond -2.000mm, please file a problem report. You can continue your print, but this indicates that the Z sensor needs to be adjusted.
  5. Contact a steward
Nozzle has plastic stuck to it

This often happens as a result of the model not sticking to the sheet, and causes problems when you try again.

⚠️ The nozzle is probably very hot! Don't touch it with something that will burn... like your fingers!


  1. Use Settings > Move axis > Move Z to raise the nozzle so you can see under it
  2. Touch some cool plastic to the still-hot plastic on the nozzle. It should stick and let you pull the mess away
  3. Heat the nozzle above the printing temperature for your filament, for example, try 250° for PLA, which normally prints around 215°. Wait for the nozzle to heat up and let the melted plastic drip off of the nozzle
  4. Use the tweezers from the tool caddy to grab larger lumps
  5. Use the soft-bristled brush in the tool caddy to wipe the warm nozzle
Other

If you are unsure, it is always best to contact a steward and fill out a problem report

Maintenance

The information below is primarily for stewards.

Regular Maintenance

The lead screws should be cleaned and lubricated regularly. This video provides a good walkthrough: How To Service Your Prusa i3 MK3

Octoprint

Octoprint - Configuration and install

The Octoprint configuration is the standard OctoPi installation, consisting of the Raspberry Pi 3 or 4 being attached to the back of the printer frame, connected via USB to the printer and via Ethernet to the ASMBLY network (WiFi connection from the Pi to the network is currently unstable), with the OctoPi 1.0.0 (build 2023.10.09.151442) stable image installed on the Pi. In an attempt to keep the printers as easily serviced and maintained, we are trying to keep the installation as standard as possible. More documentation about OctoPi can be found here. Files for printing replacement Pi 3B and Pi 4B cases can be found here:

Moving the printers

Due to the Octoprint installation on the printers, take extra care to make sure not only the main power cable is unplugged from the printer, but also the ethernet cable and the USB power cable connected to the Pi mounted to the back-upper-left corner of the printer when moving the printer around or out of the enclosure. Remember to reconnect these later.

Rebooting Procedure

In order to fully reboot the printer and the Octoprint server attached to it, power off the Pi at the back-upper-left of the printer by toggling its inline power switch, and turn the printer off using the power switch on the power supply unit at the back of the printer. Then toggle the power supply unit switch back on, and then turn the Pi back on. The Octoprint page should be reachable in under one minute.

Z Problems

If the printer is printing too far away or too close to the bed for the first layer (to see what these look like look at Section 6.3.9 of the handbook), the Z probably needs to be fine tuned. Try this:

  1. Make sure the printer knows which sheet is on the bed. Different sheets have different calibrations
  2. Run through the Calibration > First Layer Calibration process on the control panel (Section 6.3.9 of the handbook)
  3. If you have trouble calibrating Z using just the First Layer Calibration, or you want to check the calibration, these models have been useful. They may already be on the printer in a directory named Calibration. If not, create that directory and/or add these files.
    1. Calibration Network
    2. Calibration E
  4. If you have to set the Z further out than -2.000mm, the Z sensor probably needs to be adjusted. See 6.3.10.2 of the handbook
    1. The proper height for the sensor is about a zip tie's thickness
    2. If you move the Z sensor, do a Z Calibration, then calibrate the first layer again. You'll need to do this for all three sheet types, Textured, Satin, and Smooth.
Retrieved from "https://wiki.asmbly.org/index.php?title=Prusa_MK3S%2B&oldid=3155"