Asmbly Wiki - User contributions [en]

Meetings

2026-04-09T14:01:43Z

Kasper: /* Board Meetings */

There are a number of standing meetings at Asmbly.

==Community Social Hour==
The Asmbly community social is open to all and usually occurs on the first Wednesday of every month. There's no business agenda.
==Leadership Meetings==
The Executive Director (or delegate) holds monthly meetings of operational leadership (Directors, Shop Area Leads, managers) to discuss issues relevant to the day-to-day operation of Asmbly.

==Board Meetings==
The Asmbly board meets on the third Wednesday of every month. These can be virtual or in-person. Email board@asmbly.org for details if you'd like to attend. Minutes can be found in [https://drive.google.com/drive/u/1/folders/1izGozNaR1nJrbMZfT-XMzEZSffJKgcq5 Google Drive]

[[Category:Operations]]

Sawstop ICS Table Saw

2025-05-17T18:22:38Z

Kasper: Add link to Cross cut sled

Asmbly has two SawStop 10" Industrial Cabinet Saws.

* model ICS51230 5hp is owned by Asmbly
* model ICS73230 7.5hp is hosted by Danny

{{Required|Woodshop Safety}}

{{ToolPhoto|SawStop_ICS.jpg}}
{{ToolPhoto|SawStop_ICS_new.jpg}}

==Consumables==
General-purpose blades suitable for most applications are provided by Asmbly. We understand that some users may wish to provide a more application-specific blade; if this is the case, please discuss with the [mailto:workshop@asmbly.org Workshop Committee] on getting checked out to change the blade and properly adjust the SawStop brake cartridge. Inexpert blade changes can lead to misfire of the blade brake.

If you cause the brake to fire, you will be charged for a replacement! Go to the Neon store and purchase a blade and cartridge for $160.

https://asmbly.app.neoncrm.com/np/clients/asmbly/login.jsp

The SawStop system is designed to reduce the risk of personal injury when using the table saw. The brake cartridge is single-use and must be replaced after engagement. It may be falsely triggered by conductive materials, for example

* Metallic fixtures (like an aluminum miter gauge)
* Very wet wood, especially when its treated
* Metallized plastics (like mirrored acrylic)
* Heavily carbonized (ie burnt) wood
* Embedded fasteners (screws / nails / staples)

Asmbly keeps spare brake cartridges and blades in stock.

== Accessories ==
* [[Table_Saw_Sled|Table Saw Sled]]

==Resources==
* [[Media:Sawstop ICS Manual.pdf|Instruction Manual]]

==Troubleshooting==

If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:

After turning the main power switch on, the status lights will blink as the saw boots up. A solid green light with no red light indicates that the saw is ready to start. '''The saw will refuse to start while it’s still booting''', and the status lights will flash (labelled “Push Start/Stop Paddle To OFF” on the below cheat-sheet).

[[File:Sawstop system status lights.png|thumb]]
''This cheat-sheet is from page 30 in the above-linked manual. It’s also printed on the left side of the control box near the start paddle.''

The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.

If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet) is in the on position.

==Routine Maintenance==
===Clear Dust Collection Hoses===
Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages daily or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
====Procedure====
[[File:SawStopClogSmall.jpg|frameless|right]]
#Find the dust collection port behind the saw, low to the ground.
##Watch you head!
#Visually inspect the hose for a clog. The hose is slightly transparent for easy inspection. A clogged hose is heaver than you might expect. Lift the hose off the ground.
#If clogged, remove the hose clamp and hose from the saw.
#Shake the hose and gently hit the sides of the hose to remove stuck debris.
#If the dust collection port is also clogged, insert a shop vac into the port until the port is clear of debris.
#Reattach the hose.

{{Owned}}
{{Hosted|Danny Miller}}
[[Category:Woodshop]]

Table Saw Sled

2025-05-17T18:19:18Z

Kasper: Create page that contains useful information

== Cross-Cut Sled Usage on a Table Saw ==

A cross-cut sled is a jig for a table saw, significantly improving the accuracy and safety of cross-cutting operations. It provides a stable platform for the work piece and ensures cuts are square to the blade. Asmbly has several cross cut sleds available near the miter saw, the largest is 18"X36"

=== Step-by-Step Guide ===

# '''Preparation:'''
## Ensure the table saw power switch is off.
## Clean the table saw surface and the runners of the cross-cut sled to ensure smooth operation.
## Inspect the cross-cut sled for any damage or loose parts. Verify the fence(s) are securely attached and square to the blade.
## Adjust the blade height to slightly above the thickness of your work piece.
## Position your dust collection system appropriately.

# '''Work piece Placement and Securing:'''
## Place the work piece on the sled's base, ensuring it is flat and stable.
## Position the work piece against the fence of the cross-cut sled. The fence acts as a consistent reference point for your cuts.
## If making multiple cuts of the same length, ensure the work piece is firmly against the fence for each cut.
## For added stability or when cutting smaller pieces, you can use clamps to secure the work piece to the sled's base or against the fence. Ensure the clamps do not interfere with the blade's path. clamps will set off the saw stop.

# '''Making the Cut:'''
## Hold the work piece firmly to the base and fence.
## Ensure your hands are clear of the blade's path. Remember the blade will pass through the back of the fence. Use push sticks or blocks if necessary, especially for smaller pieces.
## Turn on the table saw.
## Slowly and steadily push the cross-cut sled from one of both sides. Never push from the middle as the blade will pass through the back of the sled and could cut you.
## Allow the blade to completely pass through the workpiece before stopping the sled.
## Once the cut is complete, turn off the table saw and wait for the blade to stop spinning completely before removing the workpiece and the sled.

# '''Repeat Cuts (Optional):'''
## For making multiple pieces of the same length, you can use a stop block clamped to the fence or the built in T track. Position the stop block at the desired distance from the blade.
## Place each subsequent workpiece against the stop block and the fence before making the cut. This ensures consistent lengths.

=== Safety Precautions ===
* Always wear safety glasses and hearing protection when operating a table saw.
* Never reach over or around a spinning blade.
* Keep your hands a safe distance from the blade at all times. Use push sticks or blocks when necessary.
* Ensure the workpiece is securely held against the fence and/or clamped to the sled.
* Do not force the sled through the cut. Maintain a steady and controlled feed rate.
* Allow the blade to come to a complete stop before removing the workpiece or the sled.
* Turn off the table saw when making adjustments or changing blades.
* Regularly inspect your cross-cut sled for wear and tear and ensure it is in good working order.

=== Troubleshooting ===
* '''Binding:''' If the sled binds in the miter slot, ensure the runners are the correct thickness and are clean. Alert the stewards by filing a problem report.
* '''Inaccurate Cuts:''' Verify that the fence(s) are perfectly square to the blade. An out-of-square fence will result in inaccurate cross-cuts. Alert the stewards of a misaligned sled by filing a problem report.
* '''Tear-out:''' Place sacrificial backing board between the fence and your work piece to support the wood fibers as the blade exits the back side of the workplace.

== See Also ==
* [[All Things Wood]] (for general woodworking information and other tools)
* [[Sawstop ICS Table Saw]]

[[Category:Woodshop]]

How to contribute to this wiki

2025-05-17T17:52:35Z

Kasper: Minor Additions

We welcome contributions to this wiki. Here is a quick guide to some common tasks:

==Common Tasks==

===Logging in===

To the right of the search bar at the top of the page, you should see a drop down menu that says "Anonymous". Click it, and click the "Log in" link. You should be directed to yo.asmbly.org. Log in there and you'll be logged in to the wiki. If you're already logged in to yo.asmbly.org, it should quickly direct you back.

===Editing an existing page===

When logged in, you should see "Edit" and "Edit Source" links at the top of the page. "Edit" will let you edit the current page using a web-based visual editor. "Edit Source" will let you edit the page's source in Wiki markup. You can switch between the Visual editor and the Source editor by clicking on the pencil icon at the top right of the editor.

For more information, please see this link: [https://www.mediawiki.org/wiki/Help:Editing_pages Editing Pages]

===Creating a new page===

The easiest way to create a new page is to type the title of your new page in the Search bar and hit Return. The resulting search results page will say "Create the page "Your Page Title" on this wiki!". If you click that you'll be shown an edit form for your new page.

===Creating a new page for a piece of equipment at Asmbly===

We have a page called [[Equipment Template]], which includes a lot of the basic information we need for a piece of equipment. To use it:
# "Edit Source" on [[Equipment Template]]
# copy the entire source
# create your new page (or open your existing page)
# switch to the Source editor
# paste the template
# fill in the sections

=== Formatting for Edit Source ===
For formatting guidelines, please see this link: [https://www.mediawiki.org/wiki/Help:Formatting Formatting]
This wiki uses a markup language called Wikitext or Wiki Markup. Several other how to resources are available. Large language models are fluent in wikitext.

=== Adding a page to a Category page ===
We have category pages like [[:Category:3D Printing|Category:3D Printing]]. To add a page to a category page, click the 3 line ("hamburger") menu at the top right of the editor, and select Categories. You can enter one or more categories there.

=== Inserting Links ===
For more information on inserting internal or external links into a page, please follow this link: [https://www.mediawiki.org/wiki/Help:Links Links]

=== Adding media to a page ===
On the toolbar, click Insert, and then Images and Media. The wiki will only allow you to upload files up to 2mb. If there is a video you'd like to add that doesn't already exist on the internet, request that we add it to the Asmbly Youtube page and then you can link to it from the wiki.
[[Category:Meta]]

== Navigating The wiki ==
Use the ''Special pages'' link in the sidebar to run useful reports
* [[Special:AllPages|All pages]]
* [[Special:Categories|Categories]]

Plant Stand

2025-05-17T17:31:02Z

Kasper:

A '''simple plant pot stand''' is suitable for beginners to intermediate woodworkers.

[[File:PlantStandFinished.jpg|thumb]]

== Overview ==
This project focuses on creating a sturdy and aesthetically pleasing stand primarily using a [[Sawstop ICS Table Saw|Table Saw]]. Optional steps allow for more refined details like tapered legs and rounded edges. The dimensions can be customized to fit a specific plant pot.

== Skills Needed ==
* [Optional] Milling lumber with the [[Laguna JX12 Jointer|Jointer]] and [[Powermatic 15HH Planer|Planer]]
* Ripping boards to width on the [[Sawstop ICS Table Saw|Table Saw]]
* Cross-cutting boards on the [[Sawstop ICS Table Saw|Table Saw]] using a miter fence or [[Table Saw Sled|sled]], or a [[Makita LS1219L Sliding Compound Miter Saw|compound miter saw]]
* Cutting a half-lap joint (table saw method described)
* [Optional] Using a taper leg jig on the [[Sawstop ICS Table Saw|Table Saw]]
* [Optional] Creating a roundover edge with the [[Router Table]]
* Gluing and assembling simple 90-degree joints
* Basic measuring and marking

== Materials Needed ==
* Wood: Approximately 2 inches wide and 1 inch thick. ¾ inch thick material is also suitable. Straight and flat boards can be used to avoid milling.
* Wood glue
* Sandpaper
* [Optional] Paint or other finish

== Non-Asmbly Tools Needed ==
* None

== Design and Measurements ==
The design consists of two intersecting stretcher pieces that form a cross, with four legs attached to the ends of these stretchers.
[[File:PlantStandStreach.jpg|thumb|Plant stand stretcher with dimensions.]]
[[File:PlantStandLegDem.jpg|thumb|Plant stand leg with dimensions.]]

Before starting, measure the diameter of the base of the plant pot you intend to place on the stand. The length of the stretcher pieces will depend on this measurement, ensuring the pot sits securely within the legs. The height of the legs can be adjusted based on aesthetic preference.

=== Example Dimensions ===
* '''Legs (x4):''' 1 inch thick x 2 inches wide x 14 inches long (adjust length as desired)
* '''Stretchers (x2):''' 1 inch thick x 1.5 inches wide x 8 inches long (adjust length based on pot diameter; this length would be suitable for a pot up to ~8 inches in diameter at the base)

== Procedure ==

=== 1. Milling Lumber (Optional) ===
This step is only required if your material is rough, warped, or not of the desired thickness.
# Flatten one face of your material on the [[Laguna JX12 Jointer|Jointer]]. Always use push blocks.
# Place the jointed face against the fence and flatten one edge on the [[Laguna JX12 Jointer|Jointer]], making it 90 degrees to the first face. This jointed edge will be crucial for accurate ripping.
# Use a [[Powermatic 15HH Planer|Planer]] to mill the opposite face parallel to the first, bringing the board to its final thickness (e.g., ¾ inch or 1 inch).

=== 2. Cutting Parts to Width (Ripping) ===
After milling (or if using pre-dimensioned lumber), cut the boards to their final width.
# Set the [[Sawstop ICS Table Saw|Table Saw]] fence to the desired width of your parts (e.g., 2 inches).
# Place the board on the [[Sawstop ICS Table Saw|Table Saw]] with its jointed edge (from milling step 1.2) or a factory-straight edge against the fence.
# Turn on the saw and carefully push the board through the blade, using a push stick or push block as the board nears the end of the cut, especially for the last several inches.
# Rip enough material for all four legs and two stretchers to final width.

=== 3. Cutting Parts to Length ===
# Determine the final length for your legs and stretchers based on your design.
# Use a [[Table Saw Sled]] or a miter gauge on the [[Sawstop ICS Table Saw|Table Saw]], or a [[Makita LS1219L Sliding Compound Miter Saw|compound miter saw]], to cut the four legs and two stretchers to their respective lengths from the ripped boards.
# '''Tip:''' Use a stop block when cutting multiple pieces to the same length. This ensures consistency. [[File:Stop_Block_Miter_Saw_Placeholder.jpg|thumb|Example of a stop block setup on a miter saw.]] [[File:Stop_Block_Crosscut_Sled_Placeholder.jpg|thumb|Example of a stop block setup on a table saw crosscut sled.]]

=== 4. Cutting the Half-Lap Joint ===
The two stretcher pieces will be joined at their centers using a half-lap joint.
# '''Mark the Joint:'''
## Find the center of each stretcher piece along its length and width. Mark these centerlines.
## The lap joint will be as wide as the material (e.g., 2 inches if using 2-inch wide material). Mark the outlines of the joint on both pieces, centered on the length.
# '''Set Blade Height:''' Adjust the [[Sawstop ICS Table Saw|Table Saw]] blade height to exactly half the thickness of the stretcher material. For example, if the material is ¾ inch thick, set the blade height to &frac38; inch.
# '''Cut the Joint:'''
## Using your miter gauge or [[Table Saw Sled]], make a pass on the inside edge of each marked line for the lap joint.
## Make successive passes between these initial cuts to remove the waste material. Alternatively, use a [[Dado Set and Chipper Blades|dado stack]] set to the width of the material to remove the waste in a single pass per side of the joint.
## The goal is to remove material from one stretcher piece on its top side, and from the other stretcher piece on its bottom side, so they interlock flush.
# '''Test Fit:''' The two pieces should fit together snugly, forming a flat cross. If the fit is too tight, carefully remove a small amount of additional material. If it's too loose, you may need to remake a piece or use shims if the gap is minimal.

=== 5. Tapering the Legs (Optional) ===
Tapering the legs can add a more refined look. A common taper is on the two inside faces of each leg.
# Decide on the amount of taper (e.g., from 2 inches at the top to 1 inch or 1.5 inches at the bottom. or use a 5 degree angle recommended in the plans).
# Mark the taper lines on the legs.
# Use a taper jig on the [[Sawstop ICS Table Saw|Table Saw]] to safely cut the tapers. Asmbly owns a micro jig taper jig. Watch the instructional videos produced by micro jig before using.
# Alternatively, a [[Grizzly G0817 Bandsaws|Bandsaw]] can be used to cut tapers, followed by sanding or hand planing to smooth the cut.

=== 6. Rounding Edges (Optional) ===
Rounding the edges can soften the look and feel of the stand.
# Select a roundover bit (e.g., ¼ inch or &frac18; inch radius) for the [[Router Table]].
# Adjust the router bit height and fence for the desired amount of roundover (Refer to [[Router Table]] usage guidelines).
# Carefully pass all desired edges of the legs and stretchers over the router bit. For the legs, you might choose to round the outer edges. For the stretchers, you might round the top and bottom edges. This is ultimately an ascetic choice.

=== 7. Sanding ===
# Sand all parts before assembly, starting with a medium grit [[Handheld Sanders|Sandpaper]] (e.g., 120 grit) to remove any machine marks and smooth the surfaces.
# "Break" or slightly ease any sharp edges with [[Handheld Sanders|Sandpaper]] if you did not use a router to round them over.

=== 8. Assembly and Gluing ===
# '''Dry Fit:''' Assemble the entire stand without glue to ensure all parts fit correctly. Now is the time to make any necessary adjustments.
# '''Attach the Legs:'''
## Attach two legs at to a stretcher. lay the entire assembly flat on the table ans use a single clap to provide light clamping pressure. Ensure each leg is square to the stretchers and that the assembly remains stable.
# '''Clean Up:''' Remove any glue squeeze-out immediately with a damp cloth or allow it to partially cure and then carefully pare it away with a sharp chisel or scraper.
# '''Glue the Half-Lap Joint (Optional)'''
## Apply a thin, even layer of wood glue to the mating surfaces of the half-lap joint on the stretchers.
## Join the two stretcher pieces, ensuring they are flush and square. Remove any squeeze-out with a damp cloth or a chisel once partially cured.

== Safety Considerations ==
* Always wear safety glasses when operating machinery or performing any woodworking task. Refer to the [[Woodshop Safety Class|Safety Guidelines]] page for comprehensive safety guidelines.
* Use push blocks and push sticks when working with the [[Laguna JX12 Jointer|Jointer]] and [[Sawstop ICS Table Saw|Table Saw]], especially for smaller pieces or when hands are near the blade.
* Ensure all machine guards are in place and functioning correctly.
* Read and understand the manuals for all power tools before use. Many are available on their respective tool pages on this wiki.
* Keep your work area clean and free of clutter.
* Disconnect power to tools before changing blades or bits.
* Be aware of hand placement at all times to avoid injury. Never reach over a running blade.

== See Also ==
* [[All Things Wood]] (for general woodworking information and other tools)
* [[Sawstop ICS Table Saw]]
* [[Powermatic 15HH Planer]]
* [[Makita LS1219L Sliding Compound Miter Saw|compound miter saw]]
* [[Laguna JX12 Jointer|Jointer]]
* [[Grizzly G0817 Bandsaws|Bandsaw]]
* [[Router Table]]
* [[Handheld Sanders|Sandpaper]]
* [[Woodshop Safety Class]]

[[Category:Projects]]

Bosch GCM12SD Miter Saw

2025-05-17T17:22:45Z

Kasper: Moved to Boneyard

{{Template:Boneyard}}

The Bosch GCM12SD axial-glide compound miter saw is installed in a dust collection cabinet with generous extension tables featuring adjustable stops.

{{Required|Woodshop Safety}}
{{ToolPhoto|Bosch_Miter.jpg}}

==Resources==
* [[Media:Bosch_GCM12SD_manual.pdf|Instruction Manual]]

Plant Stand

2025-05-17T17:14:59Z

Kasper:

A '''simple plant pot stand''' is suitable for beginners to intermediate woodworkers.

[[File:PlantStandFinished.jpg|thumb]]

== Overview ==
This project focuses on creating a sturdy and aesthetically pleasing stand primarily using a [[Sawstop ICS Table Saw|Table Saw]]. Optional steps allow for more refined details like tapered legs and rounded edges. The dimensions can be customized to fit a specific plant pot.

== Skills Needed ==
* [Optional] Milling lumber with the [[Delta JT360 Jointer|Jointer]] and [[Powermatic 15HH Planer|Planer]]
* Ripping boards to width on the [[Sawstop ICS Table Saw|Table Saw]]
* Cross-cutting boards on the [[Sawstop ICS Table Saw|Table Saw]] using a miter fence or [[Table Saw Sled|sled]], or a [[Bosch GCM12SD Miter Saw|compound miter saw]]
* Cutting a half-lap joint (table saw method described)
* [Optional] Using a taper leg jig on the [[Sawstop ICS Table Saw|Table Saw]]
* [Optional] Creating a roundover edge with the [[Router Table]]
* Gluing and assembling simple 90-degree joints
* Basic measuring and marking

== Materials Needed ==
* Wood: Approximately 2 inches wide and 1 inch thick. ¾ inch thick material is also suitable. Straight and flat boards can be used to avoid milling.
* Wood glue
* Sandpaper
* [Optional] Paint or other finish

== Non-Asmbly Tools Needed ==
* None

== Design and Measurements ==
The design consists of two intersecting stretcher pieces that form a cross, with four legs attached to the ends of these stretchers.
[[File:PlantStandStreach.jpg|thumb|Plant stand stretcher with dimensions.]]
[[File:PlantStandLegDem.jpg|thumb|Plant stand leg with dimensions.]]

Before starting, measure the diameter of the base of the plant pot you intend to place on the stand. The length of the stretcher pieces will depend on this measurement, ensuring the pot sits securely within the legs. The height of the legs can be adjusted based on aesthetic preference.

=== Example Dimensions ===
* '''Legs (x4):''' 1 inch thick x 2 inches wide x 14 inches long (adjust length as desired)
* '''Stretchers (x2):''' 1 inch thick x 1.5 inches wide x 8 inches long (adjust length based on pot diameter; this length would be suitable for a pot up to ~8 inches in diameter at the base)

== Procedure ==

=== 1. Milling Lumber (Optional) ===
This step is only required if your material is rough, warped, or not of the desired thickness.
# Flatten one face of your material on the [[Delta JT360 Jointer|Jointer]]. Always use push blocks.
# Place the jointed face against the fence and flatten one edge on the [[Delta JT360 Jointer|Jointer]], making it 90 degrees to the first face. This jointed edge will be crucial for accurate ripping.
# Use a [[Powermatic 15HH Planer|Planer]] to mill the opposite face parallel to the first, bringing the board to its final thickness (e.g., ¾ inch or 1 inch).

=== 2. Cutting Parts to Width (Ripping) ===
After milling (or if using pre-dimensioned lumber), cut the boards to their final width.
# Set the [[Sawstop ICS Table Saw|Table Saw]] fence to the desired width of your parts (e.g., 2 inches).
# Place the board on the [[Sawstop ICS Table Saw|Table Saw]] with its jointed edge (from milling step 1.2) or a factory-straight edge against the fence.
# Turn on the saw and carefully push the board through the blade, using a push stick or push block as the board nears the end of the cut, especially for the last several inches.
# Rip enough material for all four legs and two stretchers to final width.

=== 3. Cutting Parts to Length ===
# Determine the final length for your legs and stretchers based on your design.
# Use a [[Table Saw Sled]] or a miter gauge on the [[Sawstop ICS Table Saw|Table Saw]], or a [[Bosch GCM12SD Miter Saw]], to cut the four legs and two stretchers to their respective lengths from the ripped boards.
# '''Tip:''' Use a stop block when cutting multiple pieces to the same length. This ensures consistency. [[File:Stop_Block_Miter_Saw_Placeholder.jpg|thumb|Example of a stop block setup on a miter saw.]] [[File:Stop_Block_Crosscut_Sled_Placeholder.jpg|thumb|Example of a stop block setup on a table saw crosscut sled.]]

=== 4. Cutting the Half-Lap Joint ===
The two stretcher pieces will be joined at their centers using a half-lap joint.
# '''Mark the Joint:'''
## Find the center of each stretcher piece along its length and width. Mark these centerlines.
## The lap joint will be as wide as the material (e.g., 2 inches if using 2-inch wide material). Mark the outlines of the joint on both pieces, centered on the length.
# '''Set Blade Height:''' Adjust the [[Sawstop ICS Table Saw|Table Saw]] blade height to exactly half the thickness of the stretcher material. For example, if the material is ¾ inch thick, set the blade height to &frac38; inch.
# '''Cut the Joint:'''
## Using your miter gauge or [[Table Saw Sled]], make a pass on the inside edge of each marked line for the lap joint.
## Make successive passes between these initial cuts to remove the waste material. Alternatively, use a [[Dado Set and Chipper Blades|dado stack]] set to the width of the material to remove the waste in a single pass per side of the joint.
## The goal is to remove material from one stretcher piece on its top side, and from the other stretcher piece on its bottom side, so they interlock flush.
# '''Test Fit:''' The two pieces should fit together snugly, forming a flat cross. If the fit is too tight, carefully remove a small amount of additional material. If it's too loose, you may need to remake a piece or use shims if the gap is minimal.

=== 5. Tapering the Legs (Optional) ===
Tapering the legs can add a more refined look. A common taper is on the two inside faces of each leg.
# Decide on the amount of taper (e.g., from 2 inches at the top to 1 inch or 1.5 inches at the bottom. or use a 5 degree angle recommended in the plans).
# Mark the taper lines on the legs.
# Use a taper jig on the [[Sawstop ICS Table Saw|Table Saw]] to safely cut the tapers. Asmbly owns a micro jig taper jig. Watch the instructional videos produced by micro jig before using.
# Alternatively, a [[Grizzly G0513 Bandsaw|Bandsaw]] can be used to cut tapers, followed by sanding or hand planing to smooth the cut.

=== 6. Rounding Edges (Optional) ===
Rounding the edges can soften the look and feel of the stand.
# Select a roundover bit (e.g., ¼ inch or &frac18; inch radius) for the [[Router Table]].
# Adjust the router bit height and fence for the desired amount of roundover (Refer to [[Router Table]] usage guidelines).
# Carefully pass all desired edges of the legs and stretchers over the router bit. For the legs, you might choose to round the outer edges. For the stretchers, you might round the top and bottom edges. This is ultimately an ascetic choice.

=== 7. Sanding ===
# Sand all parts before assembly, starting with a medium grit [[Handheld Sanders|Sandpaper]] (e.g., 120 grit) to remove any machine marks and smooth the surfaces.
# "Break" or slightly ease any sharp edges with [[Handheld Sanders|Sandpaper]] if you did not use a router to round them over.

=== 8. Assembly and Gluing ===
# '''Dry Fit:''' Assemble the entire stand without glue to ensure all parts fit correctly. Now is the time to make any necessary adjustments.
# '''Attach the Legs:'''
## Attach two legs at to a stretcher. lay the entire assembly flat on the table ans use a single clap to provide light clamping pressure. Ensure each leg is square to the stretchers and that the assembly remains stable.
# '''Clean Up:''' Remove any glue squeeze-out immediately with a damp cloth or allow it to partially cure and then carefully pare it away with a sharp chisel or scraper.
# '''Glue the Half-Lap Joint (Optional)'''
## Apply a thin, even layer of wood glue to the mating surfaces of the half-lap joint on the stretchers.
## Join the two stretcher pieces, ensuring they are flush and square. Remove any squeeze-out with a damp cloth or a chisel once partially cured.

== Safety Considerations ==
* Always wear safety glasses when operating machinery or performing any woodworking task. Refer to the [[Woodshop Safety Class|Safety Guidelines]] page for comprehensive safety guidelines.
* Use push blocks and push sticks when working with the [[Delta JT360 Jointer|Jointer]] and [[Sawstop ICS Table Saw|Table Saw]], especially for smaller pieces or when hands are near the blade.
* Ensure all machine guards are in place and functioning correctly.
* Read and understand the manuals for all power tools before use. Many are available on their respective tool pages on this wiki.
* Keep your work area clean and free of clutter.
* Disconnect power to tools before changing blades or bits.
* Be aware of hand placement at all times to avoid injury. Never reach over a running blade.

== See Also ==
* [[All Things Wood]] (for general woodworking information and other tools)
* [[Sawstop ICS Table Saw]]
* [[Delta JT360 Jointer]]
* [[Powermatic 15HH Planer]]
* [[Bosch GCM12SD Miter Saw|Chop Saws]]
* [[Router Table]]
* [[Handheld Sanders|Sandpaper]]
* [[Woodshop Safety Class]]

[[Category:Projects]]

Plant Stand

2025-05-11T18:10:32Z

Kasper: First draft of a project plan for the wood shop. more edits coming soon

A '''simple plant pot stand''' is suitable for beginners to intermediate woodworkers.

[[File:PlantStandFinished.jpg|thumb]]

== Overview ==
This project focuses on creating a sturdy and aesthetically pleasing stand primarily using a [[Sawstop ICS Table Saw|Table Saw]]. Optional steps allow for more refined details like tapered legs and rounded edges. The dimensions can be customized to fit a specific plant pot.

== Skills Needed ==
* [Optional] Milling lumber with the [[Delta JT360 Jointer|Jointer]] and [[Powermatic 15HH Planer|Planer]]
* Ripping boards to width on the [[Sawstop ICS Table Saw|Table Saw]]
* Cross-cutting boards on the [[Sawstop ICS Table Saw|Table Saw]] using a miter fence or [[Table Saw Sled|sled]], or a [[Bosch GCM12SD Miter Saw|compound miter saw]]
* Cutting a half-lap joint (table saw method described)
* [Optional] Using a taper leg jig on the [[Sawstop ICS Table Saw|Table Saw]]
* [Optional] Creating a roundover edge with the [[Router Table]]
* Gluing and assembling simple 90-degree joints
* Basic measuring and marking

== Materials Needed ==
* Wood: Approximately 2 inches wide and 1 inch thick. ¾ inch thick material is also suitable. Straight and flat boards can be used to avoid milling.
* Wood glue
* Sandpaper
* [Optional] Paint or other finish

== Non-Asmbly Tools Needed ==
* None

== Design and Measurements ==
The design consists of two intersecting stretcher pieces that form a cross, with four legs attached to the ends of these stretchers.
[[File:PlantStandStreach.jpg|thumb|Plant stand stretcher with dimensions.]]
[[File:PlantStandLegDem.jpg|thumb|Plant stand leg with dimensions.]]

Before starting, measure the diameter of the base of the plant pot you intend to place on the stand. The length of the stretcher pieces will depend on this measurement, ensuring the pot sits securely within the legs. The height of the legs can be adjusted based on aesthetic preference.

=== Example Dimensions ===
* '''Legs (x4):''' 1 inch thick x 2 inches wide x 14 inches long (adjust length as desired)
* '''Stretchers (x2):''' 1 inch thick x 1.5 inches wide x 8 inches long (adjust length based on pot diameter; this length would be suitable for a pot up to ~8 inches in diameter at the base)

== Procedure ==

=== 1. Milling Lumber (Optional) ===
This step is only required if your material is rough, warped, or not of the desired thickness. For S4S (Surfaced Four Sides) lumber, this step can be skipped.
# Flatten one face of your material on the [[Delta JT360 Jointer|Jointer]]. Always use push blocks.
# Place the jointed face against the fence and flatten one edge on the [[Delta JT360 Jointer|Jointer]], making it 90 degrees to the first face. This jointed edge will be crucial for accurate ripping.
# Use a [[Powermatic 15HH Planer|Planer]] to mill the opposite face parallel to the first, bringing the board to its final thickness (e.g., ¾ inch or 1 inch).

=== 2. Cutting Parts to Width (Ripping) ===
After milling (or if using pre-dimensioned lumber), cut the boards to their final width.
# Set the [[Sawstop ICS Table Saw|Table Saw]] fence to the desired width of your parts (e.g., 2 inches). Measure from the side of the blade teeth closest to the fence.
# Place the board on the [[Sawstop ICS Table Saw|Table Saw]] with its jointed edge (from milling step 1.2) or a factory-straight edge against the fence.
# Turn on the saw and carefully push the board through the blade, using a push stick or push block as the board nears the end of the cut, especially for the last several inches.
# Rip enough material for all four legs and two stretchers to this width.

=== 3. Cutting Parts to Length ===
# Determine the final length for your legs and stretchers based on your design.
# Use a [[Table Saw Sled]] or a miter gauge on the [[Sawstop ICS Table Saw|Table Saw]], or a [[Bosch GCM12SD Miter Saw]], to cut the four legs and two stretchers to their respective lengths from the ripped boards.
# '''Tip:''' Use a stop block when cutting multiple pieces to the same length. This ensures consistency. [[File:Stop_Block_Miter_Saw_Placeholder.jpg|thumb|Example of a stop block setup on a miter saw.]] [[File:Stop_Block_Crosscut_Sled_Placeholder.jpg|thumb|Example of a stop block setup on a table saw crosscut sled.]]

=== 4. Cutting the Half-Lap Joint WIP ===
The two stretcher pieces will be joined at their centers using a half-lap joint. (If a "Half-Lap Joint" or general "Woodworking Joints" page exists, link it here).
# '''Mark the Joint:'''
## Find the center of each stretcher piece along its length and width. Mark these centerlines.
## The lap joint will be as wide as the material (e.g., 2 inches if using 2-inch wide material). Mark the outlines of the joint on both pieces, centered on the length.
# '''Set Blade Height:''' Adjust the [[Sawstop ICS Table Saw|Table Saw]] blade height to exactly half the thickness of the stretcher material. For example, if the material is ¾ inch thick, set the blade height to &frac38; inch.
# '''Cut the Joint:'''
## Using your miter gauge or [[Table Saw Sled]], make a pass on the inside edge of each marked line for the lap joint.
## Make successive passes between these initial cuts to remove the waste material. Alternatively, use a [[Dado Set and Chipper Blades|dado stack]] set to the width of the material to remove the waste in a single pass per side of the joint.
## The goal is to remove material from one stretcher piece on its top side, and from the other stretcher piece on its bottom side, so they interlock flush.
# '''Test Fit:''' The two pieces should fit together snugly, forming a flat cross. If the fit is too tight, carefully remove a small amount of additional material. If it's too loose, you may need to remake a piece or use shims if the gap is minimal.

=== 5. Tapering the Legs (Optional) WIP ===
Tapering the legs can add a more refined look. A common taper is on the two inside faces of each leg.
# Decide on the amount of taper (e.g., from 2 inches at the top to 1 inch or 1.5 inches at the bottom).
# Mark the taper lines on the legs.
# Use a taper jig on the [[Sawstop ICS Table Saw|Table Saw]] to safely cut the tapers. Ensure the outside faces of the legs remain square to the stretchers. Usually, two adjacent sides are tapered, or just the two inner-facing sides once assembled.
# Alternatively, a [[Grizzly G0513 Bandsaw|Bandsaw]] can be used to cut tapers, followed by sanding or hand planing to smooth the cut.

=== 6. Rounding Edges (Optional) WIP ===
Rounding the edges can soften the look and feel of the stand.
# Select a roundover bit (e.g., ¼ inch or &frac18; inch radius) for your [[Router Table]].
# Adjust the router bit height and fence for the desired amount of roundover (Refer to [[Router Table]] usage guidelines).
# Carefully pass all desired edges of the legs and stretchers over the router bit. For the legs, you might choose to round all four vertical edges. For the stretchers, you might round the top and bottom edges.

=== 7. Sanding WIP ===
# Sand all parts before assembly, starting with a medium grit [[Handheld Sanders|Sandpaper]] (e.g., 120 grit) to remove any machine marks and smooth the surfaces.
# Progress to finer grits (e.g., 180 or 220 grit) for a smoother finish.
# "Break" or slightly ease any sharp edges with [[Handheld Sanders|Sandpaper]] if you did not use a router to round them over.

=== 8. Assembly and Gluing WIP ===
# '''Dry Fit:''' Assemble the entire stand without glue to ensure all parts fit correctly. Make any necessary adjustments.
# '''Attach the Legs:'''
## Once the stretcher assembly is dry, apply glue to the ends of the stretchers where the legs will attach. Also, apply glue to the corresponding top inside faces of the legs.
## Attach one leg at a time. Ensure each leg is square to the stretchers and that the assembly remains stable.
## Use clamps to secure the legs to the stretchers.
# '''Clean Up:''' Remove any glue squeeze-out immediately with a damp cloth or allow it to partially cure and then carefully pare it away with a sharp chisel or scraper.
# '''Glue the Half-Lap Joint:'''
## Apply a thin, even layer of wood glue to the mating surfaces of the half-lap joint on the stretchers.
## Join the two stretcher pieces, ensuring they are flush and square. [[Clamps]] if necessary and allow the glue to set according to the manufacturer's instructions. Remove any squeeze-out with a damp cloth or a chisel once partially cured.

== Safety Considerations ==
* Always wear safety glasses when operating machinery or performing any woodworking task. Refer to the [[Woodshop Safety Class|Safety Guidelines]] page for comprehensive safety guidelines.
* Use push blocks and push sticks when working with the [[Delta JT360 Jointer|Jointer]] and [[Sawstop ICS Table Saw|Table Saw]], especially for smaller pieces or when hands are near the blade.
* Ensure all machine guards are in place and functioning correctly.
* Read and understand the manuals for all power tools before use. Many are available on their respective tool pages on this wiki.
* Keep your work area clean and free of clutter.
* Disconnect power to tools before changing blades or bits.
* Be aware of hand placement at all times to avoid injury. Never reach over a running blade.

== See Also ==
* [[All Things Wood]] (for general woodworking information and other tools)
* [[Sawstop ICS Table Saw]]
* [[Delta JT360 Jointer]]
* [[Powermatic 15HH Planer]]
* [[Bosch GCM12SD Miter Saw|Chop Saws]]
* [[Router Table]]
* [[Grizzly G0513 Bandsaw|Bandsaw]]
* [[Handheld Sanders|Sandpaper]]
* [[Woodshop Safety Class]]

[[Category:Projects]]

File:PlantStandFinished.jpg

2025-05-11T18:08:23Z

Kasper:

PlantStandFinished

File:PlantStandLegDem.jpg

2025-05-11T17:59:23Z

Kasper:

Plant stand leg with dimensions

File:PlantStandStreach.jpg

2025-05-11T17:57:49Z

Kasper:

PlantStandStreach

Sawstop ICS Table Saw

2025-05-04T23:10:33Z

Kasper: /* Clear Dust Collection Hoses */

Asmbly has two SawStop 10" Industrial Cabinet Saws.

* model ICS51230 5hp is owned by Asmbly
* model ICS73230 7.5hp is hosted by Danny

{{Required|Woodshop Safety}}

{{ToolPhoto|SawStop_ICS.jpg}}
{{ToolPhoto|SawStop_ICS_new.jpg}}

==Consumables==
General-purpose blades suitable for most applications are provided by Asmbly. We understand that some users may wish to provide a more application-specific blade; if this is the case, please discuss with the [mailto:workshop@asmbly.org Workshop Committee] on getting checked out to change the blade and properly adjust the SawStop brake cartridge. Inexpert blade changes can lead to misfire of the blade brake.

If you cause the brake to fire, you will be charged for a replacement! Go to the Neon store and purchase a blade and cartridge for $160.

https://asmbly.app.neoncrm.com/np/clients/asmbly/login.jsp

The SawStop system is designed to reduce the risk of personal injury when using the table saw. The brake cartridge is single-use and must be replaced after engagement. It may be falsely triggered by conductive materials, for example

* Metallic fixtures (like an aluminum miter gauge)
* Very wet wood, especially when its treated
* Metallized plastics (like mirrored acrylic)
* Heavily carbonized (ie burnt) wood
* Embedded fasteners (screws / nails / staples)

Asmbly keeps spare brake cartridges and blades in stock.

==Resources==
* [[Media:Sawstop ICS Manual.pdf|Instruction Manual]]

==Troubleshooting==

If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:

After turning the main power switch on, the status lights will blink as the saw boots up. A solid green light with no red light indicates that the saw is ready to start. '''The saw will refuse to start while it’s still booting''', and the status lights will flash (labelled “Push Start/Stop Paddle To OFF” on the below cheat-sheet).

[[File:Sawstop system status lights.png|thumb]]
''This cheat-sheet is from page 30 in the above-linked manual. It’s also printed on the left side of the control box near the start paddle.''

The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.

If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet) is in the on position.

==Routine Maintenance==
===Clear Dust Collection Hoses===
Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages daily or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
====Procedure====
[[File:SawStopClogSmall.jpg|frameless|right]]
#Find the dust collection port behind the saw, low to the ground.
##Watch you head!
#Visually inspect the hose for a clog. The hose is slightly transparent for easy inspection. A clogged hose is heaver than you might expect. Lift the hose off the ground.
#If clogged, remove the hose clamp and hose from the saw.
#Shake the hose and gently hit the sides of the hose to remove stuck debris.
#If the dust collection port is also clogged, insert a shop vac into the port until the port is clear of debris.
#Reattach the hose.

{{Owned}}
{{Hosted|Danny Miller}}
[[Category:Woodshop]]

File:SawStopClogSmall.jpg

2025-05-04T23:09:45Z

Kasper:

Clog in table saw hose

Sawstop ICS Table Saw

2025-05-04T16:05:47Z

Kasper: Moved ownership to the end because its not relevant to the average user. Also moved troubleshooting up for the same reason

Asmbly has two SawStop 10" Industrial Cabinet Saws.

* model ICS51230 5hp is owned by Asmbly
* model ICS73230 7.5hp is hosted by Danny

{{Required|Woodshop Safety}}

{{ToolPhoto|SawStop_ICS.jpg}}
{{ToolPhoto|SawStop_ICS_new.jpg}}

==Consumables==
General-purpose blades suitable for most applications are provided by Asmbly. We understand that some users may wish to provide a more application-specific blade; if this is the case, please discuss with the [mailto:workshop@asmbly.org Workshop Committee] on getting checked out to change the blade and properly adjust the SawStop brake cartridge. Inexpert blade changes can lead to misfire of the blade brake.

If you cause the brake to fire, you will be charged for a replacement! Go to the Neon store and purchase a blade and cartridge for $160.

https://asmbly.app.neoncrm.com/np/clients/asmbly/login.jsp

The SawStop system is designed to reduce the risk of personal injury when using the table saw. The brake cartridge is single-use and must be replaced after engagement. It may be falsely triggered by conductive materials, for example

* Metallic fixtures (like an aluminum miter gauge)
* Very wet wood, especially when its treated
* Metallized plastics (like mirrored acrylic)
* Heavily carbonized (ie burnt) wood
* Embedded fasteners (screws / nails / staples)

Asmbly keeps spare brake cartridges and blades in stock.

==Resources==
* [[Media:Sawstop ICS Manual.pdf|Instruction Manual]]

==Troubleshooting==

If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:

After turning the main power switch on, the status lights will blink as the saw boots up. A solid green light with no red light indicates that the saw is ready to start. '''The saw will refuse to start while it’s still booting''', and the status lights will flash (labelled “Push Start/Stop Paddle To OFF” on the below cheat-sheet).

[[File:Sawstop system status lights.png|thumb]]
''This cheat-sheet is from page 30 in the above-linked manual. It’s also printed on the left side of the control box near the start paddle.''

The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.

If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet) is in the on position.

==Routine Maintenance==
===Clear Dust Collection Hoses===
Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages daily or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
====Procedure====
PictureComingSoon
#Find the dust collection port behind the saw, low to the ground.
##Watch you head!
#Visually inspect the hose for a clog. The hose is slightly transparent for easy inspection. A clogged hose is heaver than you might expect. Lift the hose off the ground.
#If clogged, remove the hose clamp and hose from the saw.
#Shake the hose and gently hit the sides of the hose to remove stuck debris.
#If the dust collection port is also clogged, insert a shop vac into the port until the port is clear of debris.
#Reattach the hose.

{{Owned}}
{{Hosted|Danny Miller}}
[[Category:Woodshop]]

Sawstop ICS Table Saw

2025-05-04T15:50:42Z

Kasper:

Asmbly has two SawStop 10" Industrial Cabinet Saws.

* model ICS51230 5hp is owned by Asmbly
* model ICS73230 7.5hp is hosted by Danny

{{Required|Woodshop Safety}}

{{ToolPhoto|SawStop_ICS.jpg}}
{{ToolPhoto|SawStop_ICS_new.jpg}}

==Consumables==
General-purpose blades suitable for most applications are provided by Asmbly. We understand that some users may wish to provide a more application-specific blade; if this is the case, please discuss with the [mailto:workshop@asmbly.org Workshop Committee] on getting checked out to change the blade and properly adjust the SawStop brake cartridge. Inexpert blade changes can lead to misfire of the blade brake.

If you cause the brake to fire, you will be charged for a replacement! Go to the Neon store and purchase a blade and cartridge for $160.

https://asmbly.app.neoncrm.com/np/clients/asmbly/login.jsp

The SawStop system is designed to reduce the risk of personal injury when using the table saw. The brake cartridge is single-use and must be replaced after engagement. It may be falsely triggered by conductive materials, for example

* Metallic fixtures (like an aluminum miter gauge)
* Very wet wood, especially when its treated
* Metallized plastics (like mirrored acrylic)
* Heavily carbonized (ie burnt) wood
* Embedded fasteners (screws / nails / staples)

Asmbly keeps spare brake cartridges and blades in stock.

==Resources==
* [[Media:Sawstop ICS Manual.pdf|Instruction Manual]]

{{Owned}}
{{Hosted|Danny Miller}}
[[Category:Woodshop]]

==Routine Maintenance==
===Clear Dust Collection Hoses===
Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages daily or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
====Procedure====
PictureComingSoon
#Find the dust collection port behind the saw, low to the ground.
##Watch you head!
#Visually inspect the hose for a clog. The hose is slightly transparent for easy inspection. A clogged hose is heaver than you might expect. Lift the hose off the ground.
#If clogged, remove the hose clamp and hose from the saw.
#Shake the hose and gently hit the sides of the hose to remove stuck debris.
#If the dust collection port is also clogged, insert a shop vac into the port until the port is clear of debris.
#Reattach the hose.

==Troubleshooting==

If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:

After turning the main power switch on, the status lights will blink as the saw boots up. A solid green light with no red light indicates that the saw is ready to start. '''The saw will refuse to start while it’s still booting''', and the status lights will flash (labelled “Push Start/Stop Paddle To OFF” on the below cheat-sheet).

[[File:Sawstop system status lights.png|thumb]]
''This cheat-sheet is from page 30 in the above-linked manual. It’s also printed on the left side of the control box near the start paddle.''

The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.

If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet) is in the on position.

Sawstop ICS Table Saw

2025-05-04T15:43:51Z

Kasper: Added a section to describe how to clear the dust collection system

Asmbly has two SawStop 10" Industrial Cabinet Saws.

* model ICS51230 5hp is owned by Asmbly
* model ICS73230 7.5hp is hosted by Danny

{{Required|Woodshop Safety}}

{{ToolPhoto|SawStop_ICS.jpg}}
{{ToolPhoto|SawStop_ICS_new.jpg}}

==Consumables==
General-purpose blades suitable for most applications are provided by Asmbly. We understand that some users may wish to provide a more application-specific blade; if this is the case, please discuss with the [mailto:workshop@asmbly.org Workshop Committee] on getting checked out to change the blade and properly adjust the SawStop brake cartridge. Inexpert blade changes can lead to misfire of the blade brake.

If you cause the brake to fire, you will be charged for a replacement! Go to the Neon store and purchase a blade and cartridge for $160.

https://asmbly.app.neoncrm.com/np/clients/asmbly/login.jsp

The SawStop system is designed to reduce the risk of personal injury when using the table saw. The brake cartridge is single-use and must be replaced after engagement. It may be falsely triggered by conductive materials, for example

* Metallic fixtures (like an aluminum miter gauge)
* Very wet wood, especially when its treated
* Metallized plastics (like mirrored acrylic)
* Heavily carbonized (ie burnt) wood
* Embedded fasteners (screws / nails / staples)

Asmbly keeps spare brake cartridges and blades in stock.

==Resources==
* [[Media:Sawstop ICS Manual.pdf|Instruction Manual]]

{{Owned}}
{{Hosted|Danny Miller}}
[[Category:Woodshop]]

==Routine Maintenance==
===Clear Dust Collection Hoses===
Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages weekly or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
====Procedure====
PictureComingSoon
#Find the dust collection port behind the saw, low to the ground.
##Watch you head!
#Visually inspect the hose for a clog. The hose is slightly transparent for easy inspection. A clogged hose is heaver than you might expect. Lift the hose off the ground.
#If clogged, remove the hose clamp and hose from the saw.
#Shake the hose and gently hit the sides of the hose to remove stuck debris.
#If the dust collection port is also clogged, insert a shop vac into the port until the port is clear of debris.
#Reattach the hose.

==Troubleshooting==

If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:

After turning the main power switch on, the status lights will blink as the saw boots up. A solid green light with no red light indicates that the saw is ready to start. '''The saw will refuse to start while it’s still booting''', and the status lights will flash (labelled “Push Start/Stop Paddle To OFF” on the below cheat-sheet).

[[File:Sawstop system status lights.png|thumb]]
''This cheat-sheet is from page 30 in the above-linked manual. It’s also printed on the left side of the control box near the start paddle.''

The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.

If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet) is in the on position.