Brent Clay Extruder HD - Revision history

Smartin: /* Extruding Clay */

2025-07-23T22:25:20Z

Extruding Clay

2025-07-23T22:23:28Z

Equipment-Specific Safety

2025-07-23T22:22:59Z

Using the EZ Lock Handle & Clutch Mechanism

2025-07-23T22:21:23Z

Using the EZ Lock Handle & Clutch Mechanism

2025-07-23T22:19:49Z

Freewheel (Up Position)

2025-07-23T22:16:32Z

Using the EZ Lock Handle & Clutch Mechanism

2025-07-23T22:14:14Z

Using the EZ Lock Handle & Clutch Mechanism

2025-07-23T22:03:49Z

Using the EZ Lock Handle & Clutch Mechanism

2025-07-23T21:57:05Z

Setting a Die

2025-07-23T21:35:42Z

Operation

← Older revision		Revision as of 22:25, 23 July 2025
Line 164:		Line 164:

	*To push clay, lock the clutch into the down position		*To push clay, lock the clutch into the down position
−
−	*The clutch ensures equal pressure, regardless of how much clay remains, preventing uneven extrusion

	*Pull the handle down steadily and smoothly; the plunger will push clay through the die.		*Pull the handle down steadily and smoothly; the plunger will push clay through the die.

@@ Line 10: / Line 10: @@
 ==== Equipment-Specific Safety ====
 '''Ceramics Studio Introduction''' (CSI) is required to use this tool.
 ==== Etiquette (if relevant) ====

@@ Line 147: / Line 147: @@
 [[File:Brent clutch2.jpg|200px|thumb|right]]
-===== Locked (Down Position) =====
+'''Locked (Down Position)'''
 *Function: Engages the clutch plates
 *Use: This is the extruding mode. When the handle is down and locked into this position, it applies even pressure to push the clay through the die.
 *Result: Clay is extruded as you pull the handle down.
-===== Neutral (Middle Position) =====
+'''Neutral (Middle Position)'''
 *Function: Disengages both clutch plates
 *Use: This position releases pressure and allows the handle and plunger to move freely without engaging the clay.
 *Result: You can move the handle up or down without pushing clay — useful for repositioning or resetting.
-===== Freewheel (Up Position) =====
+'''Freewheel (Up Position)'''
 *Function: Allows quick upward motion without resistance
 *Use: When you need to quickly lift the plunger rod to reload the barrel or remove clay, this position is used.

@@ Line 162: / Line 162: @@
 *Result: Lets you crank the handle back up with minimal resistance — not for extruding.
-===== Extruding Clay =====
+==== '''Extruding Clay''' ====
 *To push clay, lock the clutch into the down position

@@ Line 162: / Line 162: @@
 *Result: Lets you crank the handle back up with minimal resistance — not for extruding.
-•	To push clay, pull down on the bottom plates—this locks the mechanism in either direction for smooth, consistent extrusion.
+*The clutch ensures equal pressure, regardless of how much clay remains, preventing uneven extrusion
-•	The clutch ensures equal pressure, regardless of how much clay remains, preventing uneven extrusion
+*Pull the handle down steadily and smoothly; the plunger will push clay through the die.
-•	Pull the handle down steadily and smoothly; the plunger will push clay through the die.
+*Collect clay coils or extruded shapes as they come out below.
-•	Collect clay coils or extruded shapes as they come out below.
+*Feed more clay as needed, always refilling before the barrel runs low for best consistency.
 == Cleanup ==

@@ Line 144: / Line 144: @@
 ** Carefully attach the end cap to the barrel of the extruder, ensuring selector plate remains in its desired position
-===== '''Using the EZ Lock Handle & Clutch Mechanism''' =====
+==== '''Using the EZ Lock Handle & Clutch Mechanism''' ====
 [[File:Brent clutch2.jpg|200px|thumb|right]]
 ===== Locked (Down Position) =====

@@ Line 131: / Line 131: @@
 ===== '''Setting a Die''' =====
-•	Choose your die and set the selector: The 3 piece die set locks into the end cap.
+*	Load the end cap
+** Place the rubber gasket ring into the base of the end cap
-•	Tighten the cap securely before operation to prevent leaks or die blowout.
+** Place the die on top of the rubber gasket ring
 ===== '''Using the EZ Lock Handle & Clutch Mechanism''' =====

← Older revision		Revision as of 21:35, 23 July 2025
Line 151:		Line 151:

	• Feed more clay as needed, always refilling before the barrel runs low for best consistency.		• Feed more clay as needed, always refilling before the barrel runs low for best consistency.
−
−
−	~~==== Feeds and Speeds - if appropriate ====~~
−
−	~~==== Controls ====~~
−
−	~~==== Settings and Adjustments ====~~
−
−	~~==== Tool Use ====~~

	== Cleanup ==		== Cleanup ==