Laguna Swift Vacuum CNC - Revision history

Rolo at 17:12, 26 February 2026

2026-02-26T17:12:53Z

2026-02-26T17:12:08Z

2026-02-20T23:30:29Z

2025-12-14T22:28:55Z

2025-06-14T23:33:42Z

2025-06-14T23:33:20Z

2025-06-14T23:19:29Z

2024-10-15T21:25:57Z

2024-02-24T19:38:20Z

Added prohibition of cutting fluids and guidelines for cutting soft metals.

2023-04-19T18:32:13Z

Resources

@@ Line 37: / Line 37: @@
 These are required after every use and should take no more than 10 seconds.
-- Rotate the handle on the filter.
+* Rotate the handle on the filter.
-- Hear the flaps flapping
+* Hear the flaps flapping
-- See the dust dropping
+* See the dust dropping
 [[File:Grizzly 1.5 G0944 .jpg|thumb|Grizzly 1.5HP G0944 Dust Collector]]
 [[Category:Woodshop]]

@@ Line 30: / Line 30: @@
 # Shut down machine using procedure on laminated sheet
 # Empty Dust Collector Barrel and Bag (if present)
-# Clean DC Filter. (Big CNC - See sticker on side of DC).
+# Clean DC Filter. (Big CNC - Rotate the handle).
 # Return/organize/close CNC toolboxes
 # Post cool pictures of your project on Discourse to encourage other members and build community
 ==Filter Cleaning Steps==
-These are required after every use and should take no more than 30 seconds.
+These are required after every use and should take no more than 10 seconds.
-[https://photos.app.goo.gl/uiUTbH2fdqTL67Fk6 Filter Cleaning Video]
+- Rotate the handle on the filter.
-''TODO Relocate video to proper in-house server.''
+- Hear the flaps flapping
-# Power On the Machine
+[[File:Grizzly 1.5 G0944 .jpg|thumb|Grizzly 1.5HP G0944 Dust Collector]]
 [[Category:Woodshop]]

@@ Line 19: / Line 19: @@
 * [[Media:SwiftManual.pdf|Owner's Manual (PDF)]]
 * [https://yo.asmbly.org/t/slab-flattening-step-by-step-instructions/7857 Slab Flattening Instructions]
 {{Owned}}

← Older revision		Revision as of 22:28, 14 December 2025
Line 1:		Line 1:
		+	{{Stub}}
		+
	Asmbly recently acquired a Laguna Swift Vacuum CNC router. It uses the same software and workflow as the [[Laguna iQ CNC]], but with a 5'x10' vacuum table work surface.		Asmbly recently acquired a Laguna Swift Vacuum CNC router. It uses the same software and workflow as the [[Laguna iQ CNC]], but with a 5'x10' vacuum table work surface.

@@ Line 33: / Line 33: @@
 ==Filter Cleaning Steps==
 These are required after every use and should take no more than 30 seconds.
 [https://photos.app.goo.gl/uiUTbH2fdqTL67Fk6 Filter Cleaning Video]
 ''TODO Relocate video to proper in-house server.''
 # Power On the Machine
 # Close Inlet Blast Gate (White Circle)

← Older revision		Revision as of 21:25, 15 October 2024
Line 19:		Line 19:

	{{Owned}}		{{Owned}}
		+	This should serve as a reference on how to properly finish up your CNC session. Please pay special attention to #6.
		+
		+	# Take out bit. Remove/return nut and collet to toolbox.
		+	# Turn off workholding vacuum, remove hold-downs, vacuum spoilboard, use chisel to flatten bumps
		+	# Use vacuum/broom to clean around machine. Don’t use airgun to just blow it away!
		+	# Sign out of Vcarve and the browser. Return shared USB drive to toolkit
		+	# Shut down machine using procedure on laminated sheet
		+	# Empty DC - both the separator and the bag
		+	# Take large scraps to dumpster
		+	# Return/organize/close CNC toolboxes
		+	# Post cool pictures of your project on Discourse to encourage other members and build community
		+
	[[Category:Woodshop]]		[[Category:Woodshop]]

← Older revision		Revision as of 19:38, 24 February 2024
Line 1:		Line 1:
	Asmbly recently acquired a Laguna Swift Vacuum CNC router. It uses the same software and workflow as the [[Laguna iQ CNC]], but with a 5'x10' vacuum table work surface.		Asmbly recently acquired a Laguna Swift Vacuum CNC router. It uses the same software and workflow as the [[Laguna iQ CNC]], but with a 5'x10' vacuum table work surface.
		+
		+	Cutting fluids are not permitted to be used on the woodshop CNC machines including the Laguna Swift and Laguna IQ CNCs.
		+
		+	Cutting of soft metals, such as aluminum and brass, is permitted on the Laguna Swift and Laguna IQ CNCs. Please be sure to clean the machine thoroughly to ensure all chips are cleared from the gantry and ways.
		+
		+	Hard metals like steel and cast iron are not permitted to be cut on the woodshop CNCs.

	{{Required\|Intro to CNC Routers}}		{{Required\|Intro to CNC Routers}}