Prusa MK3S+ - Revision history

Aneel: /* Octoprint */

2026-01-29T19:41:54Z

Octoprint

2026-01-29T19:41:21Z

2025-10-15T01:35:51Z

External Resources

2025-07-29T00:59:20Z

Booking Policies

2025-07-29T00:58:58Z

Booking Policies

2025-06-26T19:06:54Z

Z Problems

2025-06-16T21:17:20Z

Z Problems: Added pictures

2025-06-11T19:48:55Z

Resources

2025-06-11T19:48:29Z

Resources

2025-03-23T18:26:54Z

Booking Policies

@@ Line 144: / Line 144: @@
 Because the Octoprint servers are installed individually to each printer, it is safe to reboot a printer and Octoprint without disrupting the other printers in operation. This was not the case with the previous printers.
-If you are doing a print that needs to pause, for example to insert magnets, please read [Pausing prints in Octoprint]
+If you are doing a print that needs to pause, for example to insert magnets, please read [[Pausing prints in Octoprint]]
 ====== Stopping or Pausing a print ======

@@ Line 142: / Line 142: @@
 Octoprint allows you connect from the Asmbly WiFi network with a web browser or an app and start/stop a print and monitor things like the current temperature. You can't access these machines from home, you must be physically present at Asmbly.
-Because the Octoprint servers are now installed individually to each printer, it is safe to reboot a printer and Octoprint without disrupting the other printers in operation. This was not the case with the previous printers.
+Because the Octoprint servers are installed individually to each printer, it is safe to reboot a printer and Octoprint without disrupting the other printers in operation. This was not the case with the previous printers.
 ====== Stopping or Pausing a print ======

← Older revision		Revision as of 01:35, 15 October 2025
Line 205:		Line 205:

	====External Resources====		====External Resources====
		+
		+	[https://blog.rahix.de/design-for-3d-printing/ Design for 3D-Printing]
		+
	Places to find models to print:		Places to find models to print:

@@ Line 81: / Line 81: @@
 ==== Booking Policies ====
-{{Excerpt|3D_Printer_Booking_Policies|hat=0|subsections=yes|Booking Policies}}
+{{Excerpt|3D_Printer_Booking_Policies|hat=0|subsections=yes}}
 ==== Etiquette====

@@ Line 80: / Line 80: @@
 ==== Booking Policies ====
-# '''Book all of the time you need.''' Only print during time that you have booked. Don’t start prints that will go beyond your booked time. If your print has been paused or stopped because of a problem, don’t resume or restart it if it will go beyond your booked time.  If time is available after your booked time, feel free to book more time to finish your print.  If another member has already booked time that your print would need to use, and you contact them and get their approval, you may finish your print.  However, if you do not manage to contact them, or if they do not agree to let you continue, then do not start, resume, or restart prints that would go into their time.
+{{Excerpt|3D_Printer_Booking_Policies|hat=0|subsections=yes|Booking Policies}}
 ==== Etiquette====

@@ Line 295: / Line 295: @@
 ## [[:File:First layer calibration E.stl|Calibration E]]
 # If you have to set the Z further out than -2.000mm, the Z sensor probably needs to be adjusted. See 6.3.10.2 of the handbook
-## The proper height for the sensor is about a [https://help.prusa3d.com/guide/how-to-replace-superpinda-mk3s-mk3s_179920#181423 zip tie's thickness]
+## The proper height for the sensor is about 1mm. There may be some [https://help.prusa3d.com/guide/how-to-replace-superpinda-mk3s-mk3s_179920#181423 zip ties] around that can help provide a guide, but be sure to measure them with calipers. Some of the zip ties around are too flat.
 ## If you move the Z sensor, do a Z Calibration, then calibrate the first layer again. You'll need to do this for all three sheet types, Textured, Satin, and Smooth.
 [[Category:3D Printing]]

@@ Line 276: / Line 276: @@
 ==== Z Problems ====
-If the printer is printing too far away or too close to the bed for the first layer (to see what these look like look at Section 6.3.9 of the [https://cdn.prusa3d.com/downloads/manual/prusa3d_manual_mk3s_en.pdf handbook]), the Z probably needs to be fine tuned. Try this:
 # Make sure the printer knows which sheet is on the bed. Different sheets have different calibrations

@@ Line 225: / Line 225: @@
 * [https://polymaker.com/ Polymaker]
-** [https://wiki.polymaker.com/polymaker-products/printer-profiles PrusaSlicer profiles]
+** [https://wiki.polymaker.com/polymaker-products/printer-profiles Slicer profiles for PrusaSlicer and others]
 * Amazon

← Older revision		Revision as of 19:48, 11 June 2025
Line 225:		Line 225:

	* [https://polymaker.com/ Polymaker]		* [https://polymaker.com/ Polymaker]
		+	** [https://wiki.polymaker.com/polymaker-products/printer-profiles PrusaSlicer profiles]
	* Amazon		* Amazon