Sawstop ICS Table Saw - Revision history

Aneel at 22:30, 14 December 2025

2025-12-14T22:30:23Z

2025-05-17T18:22:38Z

Add link to Cross cut sled

2025-05-04T23:10:33Z

Clear Dust Collection Hoses

2025-05-04T16:05:47Z

Moved ownership to the end because its not relevant to the average user. Also moved troubleshooting up for the same reason

2025-05-04T15:50:42Z

2025-05-04T15:43:51Z

Added a section to describe how to clear the dust collection system

2025-01-03T20:39:28Z

Troubleshooting

2025-01-03T20:33:13Z

Added status-light cheat sheet and troubleshooting guide when the saw does not start.

2025-01-03T20:15:17Z

Consumables

2024-12-27T22:16:29Z

← Older revision		Revision as of 22:30, 14 December 2025
Line 1:		Line 1:
		+	{{Stub}}
		+
	Asmbly has two SawStop 10" Industrial Cabinet Saws.		Asmbly has two SawStop 10" Industrial Cabinet Saws.

← Older revision		Revision as of 18:22, 17 May 2025
Line 25:		Line 25:

	Asmbly keeps spare brake cartridges and blades in stock.		Asmbly keeps spare brake cartridges and blades in stock.
		+
		+	== Accessories ==
		+	* [[Table_Saw_Sled\|Table Saw Sled]]

	==Resources==		==Resources==

@@ Line 46: / Line 46: @@
 Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages daily or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
 ====Procedure====
-PictureComingSoon
+[[File:SawStopClogSmall.jpg|frameless|right]]
 #Find the dust collection port behind the saw, low to the ground.
 ##Watch you head!

@@ Line 29: / Line 29: @@
 * [[Media:Sawstop ICS Manual.pdf|Instruction Manual]]
-{{Owned}}
+==Troubleshooting==
-{{Hosted|Danny Miller}}
-[[Category:Woodshop]]
+If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:
 ==Routine Maintenance==
@@ Line 46: / Line 55: @@
 #Reattach the hose.
-==Troubleshooting==
+{{Owned}}
+{{Hosted|Danny Miller}}
-If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:
+[[Category:Woodshop]]

@@ Line 35: / Line 35: @@
 ==Routine Maintenance==
 ===Clear Dust Collection Hoses===
-Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages weekly or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
+Small offcuts can frequently fall into the table saw and clog the dust collection hoses. The hoses should be visually inspected for blockages daily or whenever excessive sawdust is observed during operation. When the dust collection system is working correctly, very little sawdust should accumulate around the table saw.
 ====Procedure====
 PictureComingSoon

← Older revision		Revision as of 20:39, 3 January 2025
Line 44:		Line 44:
	The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.		The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.

−	If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet~~, near the floor~~) is in the on position.	+	If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet) is in the on position.

← Older revision		Revision as of 20:33, 3 January 2025
Line 34:		Line 34:

	==Troubleshooting==		==Troubleshooting==
		+
		+	If the saw does not start when pulling the paddle, the '''two status lights''' on the control box may indicate why:
		+
		+	After turning the main power switch on, the status lights will blink as the saw boots up. A solid green light with no red light indicates that the saw is ready to start. '''The saw will refuse to start while it’s still booting''', and the status lights will flash (labelled “Push Start/Stop Paddle To OFF” on the below cheat-sheet).
		+
		+	[[File:Sawstop system status lights.png\|thumb]]
		+	''This cheat-sheet is from page 30 in the above-linked manual. It’s also printed on the left side of the control box near the start paddle.''
		+
		+	The saw may also refuse to start if it detects contact with the blade when the paddle is pulled on (labelled “Contact Detected During Standby” in the cheat-sheet). Make sure nothing (including your workpiece) is contacting the blade when starting the saw.
		+
		+	If no status lights appear after turning the main power switch on, make sure the red-and-yellow disconnect rotary switch (left side of the cabinet, near the floor) is in the on position.

@@ Line 12: / Line 12: @@
 General-purpose blades suitable for most applications are provided by Asmbly.  We understand that some users may wish to provide a more application-specific blade; if this is the case, please discuss with the [mailto:workshop@asmbly.org Workshop Committee] on getting checked out to change the blade and properly adjust the SawStop brake cartridge.  Inexpert blade changes can lead to misfire of the blade brake.
-<b>If you cause the brake to fire, you will be charge for a replacement!  Go to the Neon store and purchase a blade and cartridge for $160.</b>
+<b>If you cause the brake to fire, you will be charged for a replacement!  Go to the Neon store and purchase a blade and cartridge for $160.</b>
 https://asmbly.app.neoncrm.com/np/clients/asmbly/login.jsp
@@ Line 24: / Line 24: @@
 * Embedded fasteners (screws / nails / staples)
 Asmbly keeps spare brake cartridges and blades in stock.
 ==Resources==