Difference between revisions of "Delta 31-484 Spindle Sander"

From Asmbly Wiki
(Added photo and instructions for use)
(Removed blatantly out of date instructions about how to change the spindles.)
 
(5 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{ToolUnavailable}}
 
  
 
The Delta 31-484 is a 1hp oscillating spindle sander with a 24" square cast-iron table.  The spindle may be tilted up to 45º for sanding complex curves.
 
The Delta 31-484 is a 1hp oscillating spindle sander with a 24" square cast-iron table.  The spindle may be tilted up to 45º for sanding complex curves.
  
{{Required|Woodshop Safety}}
+
{{Required|Stationary Sanders}}
{{ToolPhoto|delta-31-484.jpg}}The spindle tilt wheel has stops at 90° and 45°; rotate clockwise to increase the angle, counterclockwise to decrease. The angle indicator may not reflect the spindle angle accurately as you adjust; as always, measure the spindle angle as you adjust. If the 90° or 45° stop positions are out of alignment, use any [https://docs.google.com/forms/d/e/1FAIpQLSfC0dq_0hp9Y5jmqknjsMoUZZQ3XVWI1MGriRb8s7MFAj1VYQ/viewform maintenance QR code] in the shop to request that they be adjusted.
+
{{ToolPhoto|delta-31-484.jpg}}
  
To change the spindle:
+
The spindle tilt wheel has stops at 90° and 45°; rotate clockwise to increase the angle, counterclockwise to decrease. The angle indicator may not reflect the spindle angle accurately as you adjust; as always, measure the spindle angle as you adjust. If the 90° or 45° stop positions are out of alignment, use any [https://docs.google.com/forms/d/e/1FAIpQLSfC0dq_0hp9Y5jmqknjsMoUZZQ3XVWI1MGriRb8s7MFAj1VYQ/viewform maintenance QR code] in the shop to request that they be adjusted.
 
 
# Remove the black table insert by lifting it out.
 
# At the rear of the machine, lift the two black handles to remove the access panel.
 
# Use the two wrenches hanging on the left side of the machine to loosen the spindle. One wrench holds the spindle seat in place, the other loosens the spindle.
 
# Unscrew the spindle by hand and store it upright in the spindle trays on either side of the machine.
 
# Screw in the new spindle and tighten using the wrenches. Hang the wrenches back on the left side when you’re finished with them.
 
# Choose a suitable table insert (hanging on the left side of the machine) for the spindle’s size and place it in the table, aligning the notch on the right side of the insert. Make sure to choose a table insert that will accommodate the angle you plan to tilt the spindle to.
 
  
 
== Resources ==
 
== Resources ==
Line 19: Line 11:
  
 
{{Hosted|Jon Eklund}}
 
{{Hosted|Jon Eklund}}
[[Category:Woodshop]]
+
[[Category:Sanding]]

Latest revision as of 19:34, 16 September 2024

The Delta 31-484 is a 1hp oscillating spindle sander with a 24" square cast-iron table. The spindle may be tilted up to 45º for sanding complex curves.


ClassWarningIcon.png Members must complete the Stationary Sanders Class before using this tool



Delta-31-484.jpg


The spindle tilt wheel has stops at 90° and 45°; rotate clockwise to increase the angle, counterclockwise to decrease. The angle indicator may not reflect the spindle angle accurately as you adjust; as always, measure the spindle angle as you adjust. If the 90° or 45° stop positions are out of alignment, use any maintenance QR code in the shop to request that they be adjusted.

Resources


Maintenance

This tool is owned by Jon Eklund and hosted at Asmbly for members to use. Please contact the workshop committee if maintenance is required.